background image

 

 

For example, if siren sound time needs to be changed to 100 seconds, the 
following procedure would be used. 
 

1. 

Press and release 

 3 times. 

2. 

Press and release 

3. 

You will see 1 parking light and 1 remote control BLUE LED flash.  You will 
also hear 1 siren chirp and 1 remote control beep.  You are now in User 
Programming Mode.  The remote control BLUE LED will flash quickly to 
signify that you are in programming mode. 

4. 

In order to access siren sound time, press and release

 .  1 remote 

control beep will occur. 

5. 

Press and release 

 .  2 remote control beeps will occur. 

6. 

The siren sound time of 100 seconds is under  

   .  So, press and 

release  

 .  3 beeps from the remote control will occur. 

7. 

Since 

 is pressed as the last button and programming is successful, 3 

parking light and remote control BLUE LED flashes will occur.  Also, 3 siren 
chirps and remote control beeps will occur. 

8. 

The siren sound time is now changed to 100 seconds. 

 
 
 

Feature 

Button 

Combination 

Options 

 

 

 

Diesel warm 

up time 

 

30 sec 

15 sec 

7.5 sec 

Siren sound 

time 

 

30 sec 

70 sec 

100 sec 

Turbo timer 

run time 

 

1 min 

2 min 

5 min 

Remote start 

reservation 

 

Automatic 

Manual  

Remote start 

run time 

 

15 min 

5 min 

25 min 

Default values. 

 
 
Valet mode ON

 

Valet mode OFF

 

 
Valet mode without remote control (Emergency shut off) 
1.  Insert the key into the key cylinder and turn to the ON position. 
2.  Within 3 seconds, press the brake pedal brake 6 times.  On the 6

th

 press, 

hold down the brake pedal. 

3.  1 parking light flash and 1 siren chirp will confirm operation. 
 

NOTE: 

This feature can be used to turn off the alarm with the key if the system 

has been triggered. 

NOTE: 

Valet mode can only be turned off via the remote control. 

 

2.9 Remote Control Hold  Button

  0.5 sec x 3 Times

 

 

Press and release 

 3 times to engage the remote control ‘Hold’ mode. 

You will see one RED LED flash and hear 1 BEEP on the remote as 
confirmation. Any button presses will be ignored.  
Press and release 

 3 times to exit remote control “Hold’ mode.  You 

will see 2 RED LED flashes and hear 2 BEEPS on the remote as 
confirmation.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Vehicle 

1 parking light flash & 1 
siren chirp 

Remote Control 

1 BLUE LED flash & 1 
beep 

Vehicle 

2 parking light flash & 2 
siren chirps 

Remote Control 

2 BLUE LED flashes & 2 
beeps 

Summary of Contents for Z-101 A



















Reviews: