CM151
2-8
CA - INSTALLER MENUS
INSTALLERS MENU 221-1387
01 PRE PX:
Used to store the customer menu adjustments
in the non-volatile memory of the EAROM . Settings for
Contrasts, Brightness, Color and Tint are stored in this
manner. 0 is custom and 7 is Pre-set stored.
02 V POS:
Moves On Screen Displays vertically. Range is
0-30. Generally set at
03 H POS:
Moves On Screen Displays horizontally. Range
is 0-45 . Generally set at
04 LEVEL:
There are three positions, 0, 1 and 2 . The
three different positions are used at the factory to
program the module for the correct features . In order
to change the level, short pins 3 and 4 together on
connector 4G9 on the main module . The connector is
located on the left hand side of the module just to the
Micro IC6000 .
Note: Be careful, shorting the wrong pins could damage
the module. Always remember to remove the
jumper after setting the level.
Level 0 and 2 is used for Private Label sets. Level 1 and
2 are used for Zenith sets . In the private label mode
the IR code is 21 or 121 .
05 BAND:
There are eight positions. 0 is Broadcast fixed,
1 is CATV afc, 3 is ICC afc, 4 is Broadcast afc, 5 CATV
fixed, 6 is HRC fixed, and 7 is ICC fixed.
06 AC ON:
There are two positions, 0 is off and I is AC
On. In On position set will turn on and off when AC
power is applied and removed.
07 RFB PF:
(RF Bandpass) Range is 0-1.
08 3.5T:
3.58 MHz trap. Range is 0-1
09 RF BRT:
(RF Brightness) Sets adjustment range of
the customer control, for brightness in RIF mode. Range
is 0-63
10 AUX BRT:
(Auxiliary Brightness) Sets adjustment range
of the customer control, for brightness in AUX mode.
Range is 0-63,
11 V SIZE:
(Vertical Size) Adjust the size of the picture
vertically. Range is-0-254.
12 H SIZE:
(Horizontal Size) Adjust the size of the
picture horizontally. Range is 0-254.
13 V PHASE:
(Vertical Phase) Shifts picture vertically .
Range is 0-7
14 H PHASE:
(Horizontal Phase) shifts picture
horizontally. Range is 0-31.
15 AUDLVL:
(Audio Level) Set gain for Composite Audio
-from Video processor. Range is 0-63.
16 RIF AGC:
Range is 0-63
17 H AFC:
There are two settings 0 and 1 . usually 1.
18 60 HZSW:
(60 Hertz compression) There are two
seftings 0 and 2. Set to 0.
19 PIFVCO:
(PIF Voltage Controlled Oscillator) Range is
0-127.
Items 20 through 24 vary with CRT*
20 R CUT:
Range is 0-254
21 G CUT:
Range is 0-254
22 B CUT:
Range is 0-254
23 G GAIN:
(Green Gain) Range is 0-254
24 B GAIN:
(Blue Gain) Range is 0-254
25 6 KEYS:
Set to 1 for the 6 button keyboard
27 A VCO:
(Audio Decoder Oscillator) Range is 0-63.
28 AFILTER:
(Audio Filter) Range is 0-63.
29 ASPECTRAL:
High Frequency separation . Range is
0-63.
30 WBAND:
(Wide Band Low Frecuency Separation)
Range is 0-63.
31 PIP X1 POS:
Range is 0-254
32 PIP Y1 POS:
Range is 0-254
33 PIP X2 POS:
Range is 0-254
34 PIP Y2 POS:
Range is 0-254
35 PIP BRIGHTNESS:
Range is 0-254
36 PIPR CONTRAST:
Range is 0-127
37 PIPG CONTRAST:
Range is 0-127
38 PIP B CONTRAST:
Range is 0-127
39 PIP ADJUST:
Range is 0-15
40 PIPY DELAY:
Range is 0-15
41 PIP BGSTART:
(PIP Burst Gate Start) Range is 0-31.
42 PIP ACCLEVEL:
Range is 0-63.
43 PIP HX:
Range is 0-63.
44 PIP VXS:
Range is 0-63.
46 PIP COMP:
Pip external syncronic. Range is 0-3.
Differences for 221-1387-01
39 PIPY DELAY:
Range is 0-15
40 PIP BGSTART:
(PIP Burst Gate Start) Range is 0-31.
41 PIP ACCLEVEL:
Range is 0-63.
42 PIP HX:
Range is 0-63
43 PIP VXS:
Range is 0-63
44 PIP COMP:
(Pip External Syncronic) Range is 0-3.
45 XTAL:
(External Crystal) Range 0-1.
* Adjust only if CRT has been changed. The “CUT”
adjustments affect the Lowlights and the “GAIN”
adjustments affect the Highlights.
