background image

4

Quick Start Installation Guide

 

806836NZ v1.02 02.22 G5 B BA Quick Start Guide

SECTION 2: IMPORTANT SAFETY INSTRUCTIONS

Safety

This appliance is not intended for use by children under 8 years or persons 
(including children under 8 years) with reduced physical, sensory or mental 
capabilities, or lack of experience and knowledge, unless they have been 
given supervision or instruction concerning the use of the appliance by 
a person responsible for their safety. Children should be supervised to 
ensure that they do not play with the appliance.

Qualifications

To avoid hazards, all installation procedures must be carried out by a 
suitably qualified tradesperson. The power cable and power outlet must be 
in a safe visible position for connection.

Venting

Sometimes steam and / or boiling water droplets may discharge through a 
vent outlet on the tap. If not using the font, ensure the tap body is located 
so the tap outlet safely dispenses into the sink bowl. 

Lifting

Take care when lifting. The Command Centre may exceed safe lifting
limits. If you feel this is beyond your personal capabilities, please seek 
assistance with the lift. The weight of the Command Centre is marked on 
the packaging. Do not lift the Command Centre by the front cover or any of 
its connections. 

!

!

Compliance

In NZ/Australia electrical installation must comply with AS/NZS3000.
In NZ/Australia plumbing installation must comply with AS/NZS3500.
In the UK the system must be installed in accordance with water supply byelaws, 
current IEE regulations and local authority byelaws.

Summary of Contents for HydroTap G5 Home Series

























Reviews: