background image

Glossary of Terms

P A G E   5 9

A list of definitions for some of the words found in this guide

75 OHM RF CABLE

The wire that comes from an off-air antenna or
cable service provider. The end looks like a 
hex-shaped nut with a wire sticking through
the middle. It screws onto the Antenna/Cable
threaded jack on the back of the L26W56X.

300 TO 75 OHM ADAPTER

A small device that connects a two-wire 300
ohm antenna to a 75 ohm RF jack.
They are usually about an inch long with two
screws on one end and a round opening with a
wire sticking out on the other end.

ANALOG TELEVISION

Standard television broadcasting format in 4:3
picture aspect ratio.

A/V CABLES

Audio/Video cables. Three cables bunched
together—right audio (red), left audio (white),
and video (yellow). A/V cables are used for
stereo playback of videocassettes and for 
higher quality picture and sound from other
A/V devices.

A/V DEVICE

Any device that produces video or sound (VCR,
DVD, cable box, or television).

AMPLIFIER

An electronic device that amplifies sound from
a television, CD player, VCR, DVD, or other
Audio/Video device.

ANTENNA

The physical receiver of television signals sent
over the air. A large metal piece of equipment
does not always have to be visible to be using
an antenna.

CABLE

Cable service box. Refers to the descrambler
box cable subscribers use to receive cable 
programming signals.

CATV

Programming provided by a cable service.

DIGITAL TELEVISION

High-resolution, cinema-quality television 
signals transmitted digitally.

DVI

Digital Video Interface
Accommodates analog and digital interfaces
with a single connector.

COMPOSITE VIDEO

Typical video jack, uses one wire for 
transporting three-color video signals.

COMPONENT VIDEO

Uses three wires for transporting three-color
video signals. The end result is usually better
video quality.

DELETED

Lets you remove channels from the list that the
end user can scroll through using CH (Channel)
Up/Down.

HDMI

High-definition multimedia interface.

HDTV

High-definition television. Refers to television
signals that have higher resolution than 
ordinary analog TV signals.

HDSTB

High-definition set top box. Refers to a tuner
device that receives high-definition television
signals which have higher resolution than 
ordinary analog TV signals.

INPUT

Refers to the input jack that receives a signal
from a TV, VCR, DVD Player or other
Audio/Video device.

JACK

An input or output connector on the back of a
TV, VCR, DVD Player or other Audio/Video
device.

MONO SOUND

Mono (monaural) sound is one channel of
sound. On more than one speaker, all the
speakers play the same audio.

OUTPUT

Refers to the output jack that sends a signal
out of a VCR, DVD, or other A/V device.

PHYSICAL CHANNEL NUMBER

Actual digital major, dashed minor channel
number that a station is broadcasting on.

RGB (Red, Green, Blue)

Connection input or output port available for
producing a video image using three separate
colors: Red, Green, and Blue.

2ND AUDIO PROGRAMMING/SAP

Second Audio Programming (SAP) is another,
separate audio channel available with some
programming. Choosing SAP often refers to 
listening to audio in another language, such as
Spanish or French.

SIGNAL

Picture and sound traveling through a cable, or
over the air, to the TV.

STEREO SOUND

Stereo (Stereophonic) sound refers to audio
that’s divided into right and left sides.

TUNER

Device that picks up the broadcast signal and
turns it into picture and sound.

VIRTUAL CHANNEL NUMBER

The arbitrarily assigned digital dashed minor
channel number that a station is broadcasting
on.

Summary of Contents for L26W56B





























































Reviews: