background image

Safety Precautions

This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product’s enclo-

sure that may be of sufficient magnitude to constitute a
risk of electric shock to persons. 

The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and mainte-
nance (servicing) instructions in the literature

accompanying the product.

NOTE TO CABLE/TV INSTALLER: 

This reminder is provided

to call the cable TV system installer’s attention to Article
820-40 of the National Electric Code (U.S.A.). The code
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
the cable entry as practical.

REGULATORY INFORMATION: 
FCC Part 15

This product has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference when
the product is operated in a residential installation. This
product generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular installa-
tion. If this product does cause harmful interference to
radio or television reception, which can be determined by
turning the product off and on, the user is encouraged to
try to correct the interference by one or more of the 
following measures: 

• Reorient or relocate the receiving antenna. 
• Increase the separation between the product and

receiver. 

• Connect the product into an outlet on a circuit 

different from that to which the receiver is 
connected. 

• Consult the dealer or an experienced radio/TV tech-

nician for help. 

FCC WARNING: 

This equipment may generate or use radio

frequency energy. Changes or modifications to this 
equipment may cause harmful interference unless the
modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is
made.

FCC COMPLIANCE: 

The responsible party for this product’s

compliance is: 
Marketed and Distributed by LG Electronics U.S.A., Inc.,
1000 Sylvan Avenue, Englewood Cliffs, NJ 
Phone: 1-847-941-8000.

IMPORTANT COPYRIGHT INFORMATION: 

Many television

programs and films are copyrighted. In certain circum-
stances copyright law may apply to private in-home video
taping of copyrighted materials.

WARNING

2

RISK OF ELECTRIC SHOCK 

DO NOT OPEN

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION:

POUR ÉVITER LES CHOC ÉLECTRIQUES, 

INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS
LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR 
MOISTURE.

MOISTURE CONDENSATION

If you pour a cold liquid into a glass, water vapor in the
air will condense on the surface of the glass. This is 
moisture condensation. Moisture condensation on the
head drum, one of the most crucial parts of the unit,
will cause damage to the tape. When the VCR is exposed
to a rapid temperature change from cold to warm, some 
condensation will occur. Under this condition, connect
the power cord to the AC line, press 

POWER 

on and

allow at least two hours for the VCR to dry out.

WARNING: 

TO REDUCE THE RISK 

OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

SERIAL NUMBER: 

The serial number is found on the back

of this unit. This number is unique to this unit and not
available to others. You should record requested informa-
tion here and retain this guide as a permanent record of
your purchase.
Model No. ___________________________
Serial No. ___________________________

Summary of Contents for VCS442









































Reviews: