Zenith ZB410, Owner'S Manual

11

10

Programming Combo Device Codes

Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/
VCR, etc.) will require you to set up two different Mode
buttons to control both parts of the Combo device. For
example, if you have a TV/DVD Combo, you might need
to set up one code under the 

TV 

button to control the

TV part AND a separate code (under any other Mode
button) to control the DVD part.

VCR/DVD/DVR Punch-Through Feature

This remote allows the 6 VCR transport buttons (i.e.

PLAY

, 

PAUSE

, 

STOP

, 

FF

, 

REWIND

, and 

REC

) to

Punch-Through control from any Mode programmed
with TV, SAT or Cable codes to the last 

VCR

, 

DVD

 or

DVR

 programmed Mode you used.  Normally other

types of remotes only punch-through (from another
Mode) on the 6 VCR buttons to the device programmed
under the 

VCR 

Mode button. This is not much use if

you are using a DVD programmed under a Mode other
than VCR. For example, if you have 2 DVD, VCR or DVR
devices programmed into this remote, the last one you
accessed on the remote will be the one that has control
of the 6 VCR transport buttons when in any other
Mode.  This feature will not operate if the programmed
TV, SAT or Cable code has its own VCR transport
button control e.g. a TV Combo, SAT/PVR, etc.

Volume/Mute Control and Punch-Through Feature

This remote lets you select which device Mode controls
your Volume/Mute buttons. The remote is initially set
(factory default) for all device Modes programmed with
“

Visual

” codes (e.g. TV, VCR, DVD, DVR, SAT &

CABLE) and “

Audio

” codes (e.g. CD & AUDIO) to use

their own Volume/Mute control if present. If the
programmed “

Visual

” code has no Volume/Mute

operation of its own then those buttons will punch-
through control to the 

TV

 Mode device without

needing to change to

 TV

 Mode. Please refer to the next

page for more information.

Setup, cont.

Setup, cont.

Any Mode chosen for Volume/Mute control MUST have

its own Volume/Mute function or the Volume/Mute

buttons will do nothing.

Setting ALL Volume/Mute Control to any one Mode

This routine can set all Modes to “punch-through” to

any one chosen Mode for Volume/Mute button control

without the needing to change to that Mode.

1. Press and hold the 

SETUP 

button until the red

indicator turns on, then release the button.

2. Press and hold the 

MUTE

 button until the red

indicator blinks off, then release the button.

3. Press and release the desired Mode button (

TV

,

SAT

, etc.) for Volume/Mute control, the red indicator

blinks then stays on.

4. Press and release the 

MUTE 

button and the red

indicator turns off. The red indicator will blink

rapidly for three seconds if the Mode you have

selected has no Volume/Mute control.

5. All other Modes will now punch-through to your

chosen Mode for Volume/Mute control.

6. All “Visual” and “Audio” programmed Modes will

now punch-through to the respective Modes you

have chosen for Volume/Mute control.

Setting any Mode to use its own Volume/Mute Control

This routine can set any Mode to use only its own

Volume/Mute control. Note - If your chosen Mode has

no Volume/Mute functions of its own then the Volume/

Mute buttons will do nothing.

1. Press and hold the 

SETUP 

button until the red

indicator turns on, then release the button.

2. Press and hold the 

MUTE

 button until the red

indicator blinks off, then release the button.

3. Press and release the desired Mode button (

TV

,

SAT

, etc.), the red indicator blinks then stays on.

4. Press and release the 

VOLUME-

 (Down) button, the

red indicator blinks then stays on.

5. Press and release the 

MUTE 

button and the red

indicator turns off.

6. All “Visual” and “Audio” programmed Modes will

now punch-through to the respective Modes you

have chosen for Volume/Mute control.