background image

 

 

 

                   IRSC Plus

 

http://www.zennio.com

 

                 

Technical Support:

 

http://support.zennio.com

 

 

13 

 

Figure 6. 

Status Window 

It is possible to activate status objects for the following actions: 

 

ON/OFF

:

 

enables the "ON/OFF (status)" binary object, which shows the A/C 

system  operation  status:  value  "1"  indicates  that  the  system  is  active, 

whereas the value "0" indicates the system is inactive.  

 

Mode

:  enables  one  status  object  per  available  mode  ("Heat  Mode  (status)", 

"Cool  Mode  (status)",  "Dry  Mode  (status)",  "Fan  Mode  (status)"  and  "Auto 

Mode  (status)")  as  well  as  the  "Mode  [1  byte]  (status)"  object.  The  first  five 

objects (1-bit) are set to "1" when their corresponding modes are active, while 

"0" indicates that the mode is not active. The 1-byte object is set to a certain 

integer value according to the currently active mode (according to Table 2)

 

Fan

:  enables  the  "Fan  (status)"  1-byte  object,  which  shows  the  current  fan 

speed, in percentage, of the A/C system (according to Table 1). 

 

Swing

:

 

enables  the  "Swing  (status)"  1-bit  object,  which  shows  the  current 

status  of the  slats  of  the  A/C  system  (if  available): the  value  "1"  means that 

the  swing  is  active,  while  "0"  indicates  that  the  slats  are  still.  Note  that  the 

swing function may differ slightly depending on the A/C system model. Please 

refer to section 3.1 for more details.  

3.4

 

RESET - INITIAL CONFIGURATION 

From  the  “Reset  (initial  configuration)”  and  the  “Reset  (data  update)”  tabs,  the 

integrator will be able to set the desired response to be performed by IRSC Plus upon 

KNX power losses as well as the initial status after a download or a device reset from 

ETS.  On  the  one  hand,  the  former  permits  defining  the  desired  status  in  the  air 

Summary of Contents for IRSC Plus



























Reviews: