© Zennio Avance y Tecnología S.L.
Edition 8
Further information
Page 2/2
SAFETY INSTRUCTIONS AND ADDITIONAL NOTES
•
Installation should only be performed by qualified professionals according to the laws and regulations applicable in each country.
•
Do not connect the mains voltage nor any other external voltage to any point of the KNX bus; it would represent a risk for th e entire
KNX system. The facility must have enough insulation between the mains (or auxiliary) voltage and the KNX bus or the wires of other
accessories, in case of being installed.
•
The facility must be equipped with a device that ensures the omnipolar sectioning. Installation of a 10 A mini-circuit-breaker is
recommended. To prevent accidents, it must remain open in case of manipulation of the device.
•
Once the device is installed (in the panel or box), it must not be accessible from outside.
•
Keep the device away from water (condensation over the device included) and do not cover it with clothes, paper or any other material
while in use.
•
The WEEE logo means that this device contains electronic parts and it must be properly disposed of by following the instructi ons at
https://www.zennio.com/en/legal/weee-regulation.
OUTPUTS SPECIFICATIONS AND CONNECTIONS
CONCEPT
DESCRIPTION
Number of outputs
4
Output type
Solid state switching device
Maximum load per output
1000 mA
Output currents
220 mA, 300 mA, 350 mA, 500 mA, 550 mA, 630 mA, 700 mA, 750 mA,
900 mA or 1000 mA.
Load type
Constant Current LED load
Short-circuit protection
YES
Overload protection
NO
Overheating protection
YES
Connection method
Screw terminal block (0.2 Nm max.)
Cable cross-section
0.2-1.5 mm² (IEC) / 16-30 AWG (UL)
EXTERNAL POWER SUPPLY SPECIFICATIONS AND CONNECTIONS
CONCEPT
DESCRIPTION
Voltage
12-30 VDC
Current
4000 mA
Connection method
Pluggable screw terminal block (0.4 Nm max.)
Cable cross-section
0.5-2.5 mm² (IEC) / 28-12 AWG (UL)
WIRING AND ASSEMBLY DIAGRAMS
LED
Each LED load must be connected according to its positive and the negative terminals. Respect always
the maximum current allowed by the loads.
Correspondence
1
: Red
2
: Green
3
: Blue
4
: White
+:
Positive terminal
-:
Negative terminal
External power supply:
+ and - terminals of external power supply (
constant
voltage)
from 12 to 30 VDC.
It is recommended to use the closest external power
supply value to the load working voltage
.
Assembly:
Screw mounting, 2 holes of
3.5 mm diameter. Screws not
included.
SEVERAL LOADS CONNECTED TO THE SAME OUTPUT
Power restriction
: It is mandatory to fulfil the next restriction
regarding the power connected to one output channel:
𝐼
𝑂𝑢𝑡
× 30
𝑉𝑑𝑐 ≥ 𝑁
𝐿𝑜𝑎𝑑𝑠
× 𝑃
𝐿𝑜𝑎𝑑
OUTPUT CURRENT SELECTOR SWITCH
*it is mandatory that the output current chosen by ETS
parameter and the current selected with the switch match
. On
the contrary, the load cannot be controlled and the test LED will
blink in white.
TEST LED ERROR IDENTIFICATION
Depending on the color, the test LED indicates different errors:
Color
Error
Blinking white
Output current selection
Blinking orange
No auxiliary power supply detected
Continuous orange
Wrong auxiliary power supply polarization
Blinking red
Overheating level 1
Continuous red
Overheating level 2
Right load wiring
✓
Wrong load wiring
Important warning:
the following rules when not
considered may result in load or device irreversible
damages
