background image

 

 

 

ZoningBOX 6 / ZoningBOX 4

 

http://www.zennio.com

 

               

Technical Support:

 

http://support.zennio.com

 

 

27 

 

Temperature  Range

  [

disabled

/enabled

]:  enables  the  global  setpoint 

restriction in the groups:  

 

Minimum  (Cool  Mode)

  [

16

…30  ºC

]:

 

minimum  global  setpoint  allowed  to 

be sent to the HVAC unit. 

 

Maximum (Heat Mode) 

[

16

…30 ºC

]:

 

maximum global setpoint allowed to 

be sent to the HVAC unit. 

This  function  involves  the  following  objects: 

[Unit  x]  Setpoint  Limits

”  (to 

activate or deactivate the temperature range restriction at any time) as well as 

[Unit x] Minimum (Cool Mode)

” and “

[Unit x] Maximum (Heat Mode)

” (to 

modify the lower and upper limits dynamically). 

 

Temperature Offset (Increase/Decrease temp. Sent to HVAC Unit) 

[

+/-0,0

 

/ +/-0,5 / +/-1,0 / +/-1,5 / +/-2,0 / +/-2,5

]: sets the value of the increment (in the 

heating mode) or the decrement (in the cooling mode) to be applied over the 

global setpoint. 

The global setpoint temperature is calculated from the value assigned to the following 

objects (as stated at the beginning of this section): 

 

[Goup  n]  [Zi]  Setpoint  Temperature

”:  Setpoint  temperature  of  each  zone 

(T

LSPi

 

[Group  n]  [Zi]  Reference  Temperature

”:  Reference  temperature  of  each 

zone (T

REFi

 

[Unit x] Return Temperature

”: Return temperature to the unit (T

RET

). 

 

[Unit x] Global Temperature Setpoint

”: Setpoint temperature of the climate 

control system (T

GSP

). 

2.2.6

 

SCENES 

It  is  possible  to  define  up  to  six  scenes  in  parameters,  whose  execution  (on  the 

reception  of  the  corresponding  scene  number  from  the  bus)  will  consist  in  setting  a 

different HVAC mode and/or a specific fan speed level. It is also possible to define the 

zone group (i.e., the HVAC unit) each scene will apply to. 

Summary of Contents for ZCL-ZB4













































Reviews: