5. Place the unit on a flat, firm place. Keep the
cutting head clear of everything around it.
6. While holding the unit firmly, pull out the
starter rope quickly.
7. After the engine has started, open the
choke guradually and allow the engine to
warm up. Pull the throttle lever to unlock it.
■
STOPPING THE ENGINE
1. Release the throttle lever.
2. Move the engine switch to the "O" position.
When using a metal blade:
1. Check the bolt to fasten the blade and be
sure the bolt has on fault, and no abrasion.
2. Be sure that the blade and the holder have
been fastened according to instruction and
the blade turns smoothly without abnormal
noise. The rotating parts fastened
incorrectly may cause serious accident to
the operator.
3. Cutting method:
a) Use the front left side for cutting.
b) Guide the blade from your right to left
with it tilted slightly to your left.
c) When mowing a wide area, start working
from your left end to avoid interference
of cut grass.
d) The blade may be seized by weeds if the
engine speed is too low, or the blade
cuts too, deep into weeds. Adjust the
engine speed and cutting depth
according to the condition of object.
For your health and to prevent the risk from
vibration, refrairr from working for a long
time at the cold temperature.
WARNING
■
SWIVEL LOCK [BC530WE]
a) When the unit is not hung down with the
harness, as in transportation, use the swivel
lock to prevent the engine from roll down.
b) To lock the swivel, turn the wing nut(1)
clockwise.
c) For normal operation, keep the wing nut
loose.
■
CUTTING WORK
•
By using the shoulder strap, hang the unit
on your right side. Adjust the strap length so
that the cutting head may become parallel
to the ground.
•
Choose a suitable recommended cutting
attachment according to the object to be
cut. Never use other cutting attachment not
approved by ZENOAH.
4. Place the unit on a flat, firm place. Keep the
cutting head clear of everything around it.
5. While holding the unit firmly, pull out the
starter rope quickly.
6. After the engine has started, open the
choke guradually and allow the engine to
warm up. Pull the throttle lever to unlock it.
5
■
STARTING THE ENGINE
Take care that the cutting head will start
rotating upon the engine starts.
A: BC2300LE/BC2600LE/BC3500WE/BC4500WE
1. Push the primer pump(1) several times until
overflown fuel flows out in the clear tube.
2. Move the choke lever(2) to the closed
position.
3. Set the engine switch(a) to the " I " position.
Set the throttle lever to the start position (1-
2-3).
B: BC530WE
1. Open the fuel shutoff valve. (1)
2. While pushing the tickler lever(3), push the
primer pump(2) several times until the flow
of fuel into the overflow pipe.
3. Move the choke lever(4) to the closed
position.
4. Set the engine switch(a) to the " I " position.
Set the throttle lever to the start position (1-
2-3).
Use
■
ADJUSTMENTS
•
Throttle cable: The normal play is 1 or 2 mm
when measured at the carburetor side end.
Readjust with the cable adjuster(1) as re-
quired.
•
Engine idling speed: It is normal that the
engine keeps running without the blade
rotation, when the throttle lever is released.
When the engine speed is too high or too
slow, readjust the idle set screw (2).
BC2300LE
BC2600LE
BC3500WE
BC4500WE
BC2300LE
BC2600LE
BC2300LE
BC2600LE
BC3500WE
BC4500WE
BC3500WE
BC4500WE
BC530WE
BC530WE
