background image

GB-13

BK3420FL-EZ

G

B

7. Fuel

 FUEL

WARNING

•  Gasoline  is  very  flammable.  Avoid  smo king  or 

bringing any flame or sparks near fuel. Make sure 

to stop the engine and allow it cool before refueling 

the unit. Select outdoor bare ground for fueling and 

move at least 3 m (10 ft) away from the fueling point 

before starting the engine.

•  The  Zenoah  engines  are  lubricated  by  oil  specially 

formulated for air-cooled 2-stroke gasoline engine use. 

If  Zenoah  oil  is  not  available,  use  an  anti-oxidant 

added  quality  oil  expressly  labeled  for  air-cooled 

2-stroke engine use (JASO FD GRADE OIL or ISO-L-

EGD GRADE).

•  Do not use BIA or TCW (2-stroke water-cooling type) 

mixed oil.

 RECOMMENDED MIXING RATIO

  GASOLINE 25 : OIL 1

  When using  market oil (JASO FB grade oil or ISO-

L-EGB grade oil)

  GASOLINE 50 : OIL 1

  When using ZENOAH genuine oil, JASO FD grade 

oil or ISO-L-EGD grade oil

•  Exhaust  emission  are  controlled  by  the  funda­

mental  engine  parameters  and  components  (eq., 

carburation, ignition timing and port timing) without 

addition of any major hardware or the introduction 

of an inert material during com bustion.

•  These engines are certified to operate on unleaded 

gasoline.

•  Make  sure  to  use  gasoline  with  a  minimum  octane 

number of 89RON (USA/Canada: 87AL).

•  If  you  use  a  gasoline  of  a  lower  octane  value  than 

prescribed,  there  is  a  danger  that  the  engine  tem-

perature  may  rise  and  an  engine  problem  such  as 

piston seizing may consequently occur.

•  Unleaded  gasoline  is  recommended  to  reduce  the 

contamination of the air for the sake of your health and 

the environment.

•  Poor  quality  gasolines  or  oils  may  damage  sealing 

rings, fuel lines or fuel tank of the engine.

 HOW TO MIX FUEL 

WARNING

•  Pay attention to agitation.

1.  Measure out the quantities of gasoline and oil to be 

mixed.

2.  Put some of the gasoline into a clean, approved fuel 

container.

3.  Pour in all of the oil and agitate well. 

4.  Pour in the rest of gasoline and agitate again for at 

least  one  minute.  As  some  oils  may  be  difficult  to 

agitate depending on oil ingredients, sufficient agita-

tion is necessary for the engine to last long. Be care-

ful that, if the agitation is insufficient, there is an in-

creased danger of early piston seizing due to abnor-

mally lean mixture.

5.  Put a clear indication on the outside of the container 

to avoid mixing up with gasoline or other containers.

6.  Indicate the contents on outside of container for easy 

identification.

 FUELING THE UNIT 

1.  Untwist and remove the fuel cap. Rest the cap on a 

dustless place.

2.  Put fuel into the fuel tank to 80% of the full capacity.

3.  Fasten  the  fuel  cap  securely  and  wipe  up  any  fuel 

spillage around the unit.

WARNING

1.  Select flat and bare ground for fueling.

2.  Move  at  least  10  feet  (3  meters)  away  from  the 

fueling point before starting the engine.

3.  Stop the engine before refueling the unit. At that 

time,  be  sure  to  sufficiently  agitate  the  mixed 

gasoline in the container.

 FOR YOUR ENGINE LIFE, AVOID: 

1.  FUEL WITH NO OIL (RAW GASOLINE) – It will cause 

severe  damage  to  the  internal  engine  parts  very 

quickly.

2.  GASOHOL – It can cause deterioration of rubber and/

or plastic parts and disruption of engine lubrication.

3.  OIL FOR 4-CYCLE ENGINE USE – It can cause spark 

plug  fouling,  exhaust  port  blocking,  or  piston  ring 

sticking.

4. 

Mixed fuels which have been left unused for a pe-

riod of one month or more

 may clog the carbu retor 

and result in the engine failing to operate properly.

5.  In the case of storing the product for a long period of 

time, clean the fuel tank after rendering it empty. Next, 

activate the engine and empty the carburetor of the 

composite fuel. 

6.  In the case of scrapping the used mixed oil container, 

scrap it only at an authorized repository site.

NOTE

As for details of quality assurance, read the description 
in the section Limited Warranty carefully. Moreover, nor-
mal wear and change in product with no functional influ-
ence are not covered by the warranty. Also, be careful 
that, if the usage in the instruction manual is not observed 
as to the mixed gasoline, etc. described therein, it may 
not be covered by the warranty.

01-BK3420FL-EZ_GB_207_三.indd   13

12.9.21   1:24:15 PM

Summary of Contents for BK3420FL-EZ























Reviews: