background image

GB-2

BK3420FL-EZ

1. Parts location

Contents

  1.  Parts location ...................................................2
  2.  Specification ....................................................3
  3.  Symbols on the machine ..................................3
  4.  Warning labels on the machine .......................4
  5.  For safe operation ............................................5
  6.  Set up ...............................................................9
  7.  Fuel ................................................................13
  8.  Operation .......................................................14
  9.  Maintenance ..................................................17
  10.  Troubleshooting ..............................................21
  11.  Disposal .........................................................21

  1.  Muffler
  2.  Fuel tank
  3.  Fuel tank cap
  4.  Shoulder frame
  5.  Shoulder belt
  6.  Hanging belt
  7.  Air cleaner
  8.  Spark plug
  9.  Fuel cock
 10.  Carburetor
  11.  Recoil starter
 12.  Choke lever
 13.  Gear case
 14.  Tangle-prevention cover
 15.  Blade
 16.  Blade cover
 17.  Debris guard
 18.  Main pipe
 19.  Loop handle
 20.  Throttle lever
 21.  Right-hand grip
 22.  Throttle wire
 23.  Wire clamp
 24.  Engine stopping switch
 25.  Flexible shaft

 SAFETY FIRST

Instructions  contained  in  warnings  within  this  manual  marked 
with a   symbol concern critical points which must be taken into 
consideration to prevent possible serious bodily injury, and for 
this reason you are requested to read all such instructions care-
fully and follow them without fail.

NOTES ON TYPES OF WARNINGS IN THE MANUAL

 WARNING

This mark indicates instructions, which must be followed in order 
to prevent accidents, which could lead to serious bodily injury 
or death.

 IMPORTANT

This mark indicates instructions, which must be followed, or it 
leads to mechanical failure, breakdown, or damage.

 NOTE

This mark indicates hints or directions useful in the use of the 
product.

01-BK3420FL-EZ_GB_207_三.indd   2

12.9.21   1:24:08 PM

Summary of Contents for BK3420FL-EZ























Reviews: