background image

11

11. Parts List : BM40S

Key#

Part KIT Number

Description

Q'ty

1

RMKIT01AS

Tank strainer.

1

2

RMKIT527

Red tank Lid with integrated handle, duck valve & seal.

1

3

RMKIT528

• Duck valve for Lid.

1

4

RMKIT02A

• Seal for cap 6".

1

5

RMKIT04

Nylon bearings.

1

6

RMKIT05

Pump lever set.

1

7

RMKIT06

• Screw and nut set.

1

8

RMKIT07

Pump handle (fold-back type).

1

9

RMKIT10

Presseure tank O-ring.

1

10

RMKIT11

Retention clamp.

1

11

RMKIT16

90 degree fitting & clamp.

1

12

RMKIT17

Hose & 2 hose clamps

1

13

RMKIT18F

Complete spray pistol w/Built-ln Filter & Grip.

1

14

RMKITFILT

• Filter for kit 18F.

1

15

RMKITGRIP

• Grip handle for kit 18F.

1

16

RMKIT19

• Spindle set.

1

17

RMKIT20

• Spindle O-ring set.

1

18

RMKIT21

• Plug set.

1

19

RMKIT367

• O-ring set

1

20

RMKIT22

Brass spray wand.

1

21

RMKIT392

Washer set for gun and nozzle.

1

22

RMKIT25

Adjustable brass nozzle w/nozzle holder.

1

23

RMKIT24

• Nozzie holder.

1

24

RMKIT26

• Spray tip O-ring Nitril.

1

25

RMKIT180

Locking pins-pump handle (small).

1

26

RMKIT181

Locking pin pump handle (large).

1

27

RMKIT250

Complete pump module.

1

28

RMKIT251

• Complete cylinder for sealed piston.

1

29

RMKIT12.1

• • O-ring & washer set for diaphragm and piston.

1

30

RMKIT252

• Halph moon Jaws and Clamps

1

31

RMKIT253

• Piston Holder and stainless plate

1

32

RMKIT254

• Brass hollow shaft.

1

33

RMKIT256

• Complete base & seals.

1

34

RMKIT255

• Viton piston and seals.

1

35

RMKIT257

• Nylon crank & brass bushing.

1

36

RMKIT258

• Lever Holding Saddle w/bolt and nut

1

37

RMKIT259

• Bolt & nut piston holder.

1

38

RMKIT284

Heavy duty Padded, adjustable shoulder straps.

1

39

RMKIT31

• Belt Hook & Buckle

2

40

RMKIT283

• • Belt hook.

2

41

RMKIT510

Special solvent resistent pressure chamber.

1

Summary of Contents for BM40S













Reviews: