background image

For safe operation and maintenance, symbols are
carved in relief on the machine. According to these
indications, please be careful not to make a
mistake.

(a) The port to refuel the "MIX GASOLINE" 
Position: FUEL TANK CAP

(b) The direction A to close the choke

The direction B to open the choke

Position: AIR CLEANER COVER

(c) This unit is fitted with only flexible line cutter.

Never use cutting blade made of metal or
plastic.

Position: DEBRIS GUARD

4. Symbols on the machine

(1) Read owner's manual before operating machine.
(2) Wear head, eye and ear protection.
(3) Wear foot protection.
(4) Wear gloves.
(5) Beware of thrown objects.
(6) Warning / Attention
(7) Keep all children, bystanders and helpers 15 meters away from the brushcutter

If warning label peel off or become soiled and impossible to read, you should contact the dealer
from which you purchased the product to order new labels and affix them in the required
location(s).

Never modify your brushcutter.
We won't warrant the machine, if you use the remodeled brushcutter or you don't observe
the proper usage written in the manual.

WARNING

IMPORTANT

15m (50ft)

(1)

(2)

(3)

(4)

(5)

(6)

(7)

3. Warning labels on the machine

4

Summary of Contents for BT251

























Reviews: