background image

GB-5

G

B

EX2600

4. Symbols on the machine

For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, 
please be careful not to make a mistake.

The port to refuel the “MIX GASOLINE”

Position: FUEL TANK CAP

The direction to close the choke
Position: AIR CLEANER COVER

The direction to open the choke
Position: AIR CLEANER COVER

3. Warning labels on the machine

Never modify your machine.
We won’t warrant the machine, if you use the 
remodeled brushcutter or if you don’t observe 
the proper usage written in the manual.

If warning label peels off or becomes soiled and 
impossible to read, you should contact the 
dealer from which you purchased the product 
to order new labels and affix them in the required 
location (s).

15m (50ft)

 (1)  (2)  (3)  (4)  (5) 

(6) 

(7)

(1) Read owner’s manual before operating this machine.
(2) Wear head, eye and ear protection.
(3) Wear foot protection.
(4) Wear gloves.
(5) Beware of thrown objects.
(6) Warning / Attention
(7) Keep all children, bystanders and helpers 15 meters away from the machine.

The direction to adjust the chain oil flow.
Turn to “+” (clockwise) : increase, 
Turn to “-” (counter-clockwise) : decrease.
Position: Upper side of the TRANSMISSION

(PS-EX2 only)

 01-EX2600_GB_cs5_二.indd   5

17/04/14   18:09

Summary of Contents for EX2600































Reviews: