background image

Author: RK 

Version: 2.3 

Revision: 1.4 

Revision Date: February 2022 

 

3.   Open flap B. 

 

4.   Keep  the flame failure  device knob (A)  pressed  in for  approximately 5  seconds 

to allow gas to flow to the burner. 

 

5.   Strike  a  match  and  insert  into  flap  hole  (B). W hile  the  flame  is  burning  press 

and  hold  the flame failure  device for  a further  10 seconds. The  burner  will  now 
burn with a blue flame. 

 

6.   If the flame goes out, repeat steps 4, 5 and 6 until the flame stays alight. 

 

7.   

The appliance should be left running for a minimum of 12 hours 

before being loaded with products.

 

 

8.     To  terminate  the gas  operation  turn  off  the shut-off  valve  on  the  gas  bottle  or 

gas installation. 

 

USERS  NOTE:    

The  gas  safety  valve  knob  (A)  should  never  be  depressed for  periods 

longer  than 5 seconds with the burner unlit as this can cause a potentially dangerous build- 

up of unburnt gas. If the burner does not ignite, allow sufficient time for any unburnt gas to 

disperse, and then repeat the ignition steps. 

 

TROUBLESHOOTING

 

 

IF THE APPLI ANCE F AILS TO WORK:

 

 

Check the following points before calling for service:

 

 

1.   That the instructions for starting the appliance have been followed. 

 

2.   The appliance is level. 

 

3.   If it is possible to start the appliance on an alternative energy sources. 

 

4.   If the appliance fails to work on gas, check: 

a)   That the gas bottle is not empty. 

b)   That the regulator is not faulty. 

c)   If another appliance is connected to the same supply, check if it works 

properly. 

 

5.   If the appliance fails to work on 230V (Mains Electricity), check: 

a)   That the 230V supply is connected to the unit. 

b)   That there are no loose connections. 

c)   That the heating element has not burnt out. 
d)   Check if electric supply is on by feeling if hot air comes out of the top of the 

flue (chimney. This will take about 1 hour after switching on). 

 

IF THE APPLI ANCE IS NOT COLD ENOUGH IT MAY BE BECAUSE:

 

 

1.   The ventilation of the absorption unit is inadequate.  Allow at least 100mm 

around Back, sides, and 600mm above. 

 

2.   The evaporator is frosted up – see Defrosting page 7.

Summary of Contents for GF180IP













Reviews: