background image

6

IMPORTANT INFORMATION - PLEASE READ BEFORE USE

 BATTERY 

SAFETY

       When handled incorrectly, Lithium polymer batteries can be dangerous and 

can potentially harm and do damage to persons or property. Zero-X does 
not accept any liability of damage to persons or property if the battery is not 
correctly charged, stored or protected.

    • 

 

Always unwind all cables before charging.

    • 

 

Do not over charge the battery. Once the charging process is completed, 
remove the battery from the charger as soon as possible.

    • 

 

You must charge the Lithium polymer battery in a safe area away from 
flammable materials.

    • 

 

 Only use the included, or replacement Zero-X Rapture

HD

 compatible 

chargers and batteries.

    • 

 

 The battery is only to be charged under adult supervision, do not leave 
charging batteries unattended. You should always remain in constant 
observation to monitor the charging process and react immediately to any 
potential problems that may occur.

    • 

 

Do not charge the battery in temperatures hotter than 40°C or colder than 
0°C.

    • 

 

Do not cover the batteries when charging. Do not leave batteries in direct 
sunlight. 

      • After each flight & or crash, please check battery for any damage or swelling.

    • 

 

If the batteries are damaged, leaking, making noise, punctured or 
malformed in any way DO NOT attempt to use it. Please dispose of the 
battery immediately and safely in the correct manner.

    • 

 

 Do not bend, puncture, crush or scratch the drone’s batteries. Do not store 
batteries in your pockets, on your person or in extreme temperatures.

    • 

 

After flying/discharging the battery you must allow it to cool to ambient/
room temperature before recharging.

    • 

 

If at any time during the charge or discharge process the battery begins to 
balloon or swell, discontinue charging or discharging immediately. Quickly 
and safely disconnect the battery, then place it in a safe, open area away 
from flammable materials to observe it for at least 15 minutes. Continuing to 
charge or discharge a battery that has begun to balloon or swell can result 
in a fire. A battery that has ballooned or swollen even a small amount must 
be removed from service completely.

    • 

 

Never plug in a battery and leave it to charge unattended overnight.

    • 

 

Non-compliance with the above warnings may result in the failure of the 
battery.

Summary of Contents for RAPTURE HD ZX-RHD

























Reviews: