background image

Installation & Operation  •  11

INSTALLATION & OPERATION

Alternate Bumper Splice & glass Front Splice

Some cases will have the alternate bumper with optional glass front. When joining two of these cases together, special splice pieces will be 

provided (

See Figure 15

). First, hook the bumper splice over the bumper and fasten it under the bumper so it covers the seam. Next, slide the 

glass front splice down over the glass fronts and fasten it to the inside of the case.

Drain

The drain can be accessed through the drain access port in the center of the floor pan in the bottom of the case (

See Figure 16

). The 1 1/2" 

PVC drain outlet is located at the center front of the case behind the kickplate.

The drain line exits the case in the center. The lateral runs of drain pipe should be installed through the bases (

See Figure 17

). There is no 

room in front of the base for the drain pipe because the kickplate installs directly to the front of the bases.

Install the drain tee to the outlet pipe and a drain trap to the tee. Plug the open end of the tee using the clean-out plug supplied with the drain 

trap kit. The drain line must be pitched away from the case. The tee, drain trap, and plug are supplied with the case. The drain trap must be 

level. The drain trap should be primed with water after installation. The drain line must be pitched away from the case enough to ensure proper 

drainage. Consult your local codes for minimum requirements.

The forward drain section, tee, and “R” trap are shipped loose for field installation.

 FIGURE 15: Splices for Optional Glass Front

Alternate Bumper Splice 

(fasten in front)

glass Front Splice 

(fasten inside case)

 FIGURE 16: Drain Access Port

 FIGURE 17: Drain Installation

Summary of Contents for Reveal Merchandiser ORMC75-MX
























Reviews: