www.scheppach.com /
service@scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
GB | 19
We accept no liability for accidents or damage that
occur due to a failure to observe this manual and the
safety instructions.
2. Device description
1. Additional retainers
2. Transport handles
3. Claw
4. Riving knife
5. Riving bar
6. Table
7. Wheels
8. Oil dipstick
9. Stroke setting bar
10. Control handle
11. Complete control arms
12. Tray table (lateral)
13. Combination switch/plug
14. Motor
15. Cover
3. Scope of delivery
A. Splitter
B. Control arms
C. Claw
D. Additional retainers
E. Wheels
F. Table
G. Safety bar
H. Enclosed accessories bag (a, b, c)
a - Cylindrical screw M10 x 100 mm including four
washers and self-locking nuts (2x)
b - Bolt with cotter pin (2x)
c - Hexagon screw M8 x 25 mm including self-locking
nuts (4x)
I. Tray tables (lateral)
J. Operating manual
4. Intended use
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufactur-
er will be liable for any damage or injuries of any kind
caused as a result of this.
To use the equipment properly you must also ob-
serve the safety information, the assembly instruc-
tions and the operating instructions to be found in
this manual. All persons who use and service the
equipment have to be acquainted with this manual
and must be informed about the equipment’s poten-
tial hazards. It is also imperative to observe the ac-
cident prevention regulations in force in your area.
The same applies for the general rules of health and
safety at work.
1. Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschine GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
•
Applicationlotherlthanlspecified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operat-
ing instructions contain important information on how
to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, re-
duce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regu-
lations that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture.
Read the instruction manual each time before op-
erating the machine and carefully follow its informa-
tion. The machine can only be operated by persons
who were instructed concerning the operation of the
machine and who are informed about the associat-
ed dangers. The minimum age requirement must be
complied with.
In addition to the safety instructions in this operating
manual and the separate regulations of your country,
the generally recognised technical rules for operat-
ing woodworking machines must also be observed.
