background image

1 General notes

1.1 Structure of the operating instructions

Before installation and start-up, read this manual carefully to ensure correct use!

We emphasize that these operating instructions apply to speci

c units only, and are in no way

valid for the complete system!

Use these operating instructions to work safely with and on the device. They contain safety instruc-

tions that must be complied with as well as information that is required for failure-free operation of the

device.

Keep these operating insturctions together with the device. It must be ensured that all persons that

are to work on the device can refer to the operating instructions at any time.

Keep the operating instructions for continued use. They must be passed-on to all successive owners,

users and

nal customers.

1.2 Target group

The operating instructions address persons entrusted with planning, installation, commissioning and

maintenance and servicing and who have the corresponding quali

cations and skills for their job.

1.3 Exclusion of liability

Concurrence between the contents of these operating instructions and the described hardware and

software in the device has been examined. It is still possible that non-compliances exist; no guarantee

is assumed for complete conformity. To allow for future developments, construction methods and

technical data given are subject to alteration. We do not accept any liability for possible errors or

omissions in the information contained in data, illustrations or drawings provided.

Ziehl-Abegg AG is not liable for damage due to misuse, incorrect use, improper use or as a

consequence of unauthorized repairs or modi

cations.

1.4 Copyright

These operating instructions contain copyright protected information. The operating instructions may

be neither completely nor partially photocopied, reproduced, translated or put on data medium without

previous explicit consent from Ziehl-Abegg AG. Infringements are liable for damages. All rights

reserved, including those that arise through patent issue or registration on a utility model.

2 Safety information

This chapter contains instructions to prevent personal injury and property damage. These instructions

do not lay claim to completeness. In case of questions and problems, please consult our company

technicians.

2.1 Use as intended

The equipment is to be used solely for the purposes speci

ed and con

rmed in the order. Other uses

which do not coincide with, or which exceed those speci

ed will be deemed unauthorised unless

contractually agreed. Damages resulting from such unauthorised uses will not be the liability of the

manufacturer. The user will assume sole liability.

Reading these operating instructions and complying with all contained instructions

especially the

safety noti

cations contained therein

are considered part of intended use. To consider is also the

manual of attached components. Not the manufacturer, rather the operator of the device is liable for

any personal harm or material damage arising from non-intended use!

Operating Instructions

Acontrol

model series PKE-6 /-10 / PKE-14

General notes

L-BAL-E042-GB 1002 Index002

Part.-No. 00163314-GB

3/26

Summary of Contents for Acontrol PKE-6




























Reviews: