background image

9.6

Statistic menu

All statistical data can be called up in the 

Statistics 

menu. The data will be retained even after the 

ZArec4C has been switched off. Reading out the error list and deleting the error memory are 
described in the chapter "Error diagnosis". 

Parameter

Designation

Value range

Factory set-

ting

ST_LST 

Error list

Cannot be set

-

ST_H 

Operating hours

Cannot be set

-

ST_DRV 

Number of trips

Cannot be set

-

ST_RES 

Number of mains interruptions

Cannot be set

-

ST_GE

Number of mains disturbances

Cannot be set

-

ST_SD

Number of mains disturbances

Cannot be set

-

ST_CLR

Delete error memory
Deletion of ST_LST and ST_RES

On
Off

Off

RESET

99:

 Device reset, parameters are deleted and set to factory 

settings. 

Software version number (e.g.: Version 4.01 -> "401"):

 Reset 

parameters ST_H, ST_DRV, ST_RES as well as the energy 
meter and the system time. Recorder settings are overwritten by 
factory settings. 

0...65535

0

9.7

Memory Card menu

Contains the parameters for the various functions in association with a memory card.

Parameter

Designation

Value range

Factory set-

ting

SAV_ALL

Saves error lists (.FLT) and printer lists (.PRT) to memory card 
with serial number allocation.
The lists are saved in the ZR4/DEVICE/SerialNumber/LST fold-
er.

Off:

 no function

ON:

 Error list and printer list are saved on memory card. The 

parameter jumps back to "Off" after saving. 

On
Off

Off

SAV_PAR

Save parameters to memory card (copy parameters in the case 
of identical systems):

Parameter (.PA3) in the folder /ZR4/DEVICE/FORCE

Here, there is no serial number allocation. The data will be over-
written during each saving

Off:

 no function

ON:

 Parameters are saved on memory card. The parameter 

jumps back to "Off" after saving. 

On
Off

Off

LOD_PAR

Load parameters from memory card to the ZArec4C (copy pa-
rameters in the case of identical systems) 

Input 27:

 Parameters (.PA3) are loaded from the /ZR4/DEVICE/-

FORCE folder into the ZArec4C. The parameter jumps back to 
"Off" after loading. 

0...27

0

Original operating instructions

ZArec4C

Parameter list

R-TBA14_03-GB 1817 Index 007

Part.-No. 00163436-GB

44/64

Summary of Contents for ZA rec 4C Series

































































Reviews: