5
STH-03ZB User's Manual
6. Setting Transmission Interval for STH-03ZB
6.1
If necessary, remove STH-03ZB from mounting cradle (see
"
Installing Mounting for
STH-03ZB
""""
section).
6.2 Using the following setting positions to set the appropriate transmission interval for
STH-03ZB:
Transmit Interval
DIP Switch Setting Transmit Interval
DIP Switch Setting
1 Second
1 Minute
5 Seconds
5 Minutes
10 Seconds
10 Minutes
15 Seconds
15 Minutes
20 Seconds
20 Minutes
25 Seconds
25 Minutes
30 Seconds
30 Minutes
35 Seconds
35 Minutes
40 Seconds
40 Minutes
45 Seconds
45 Minutes
50 Seconds
50 Minutes
55 Seconds
55 Minutes
60 Seconds
60 Minutes
65 Seconds
65 Minutes
70 Seconds
70 Minutes
75 Seconds
75 Minutes
6.3 Ensure STH-03ZB is connected to a coordinator device (see
"
Adding STH-03ZB to
Receiving Device
""""
section).
6.4 Use QuickView Data PS software on PC with coordinator device to confirm STH-03ZB
transmissions are being received and the update interval has been set correctly.
6.5 Replace STH-03ZB into mounting cradle (see
"
Installing Mounting for STH-03ZB
""""
section)
as required.
6.6 Transmission interval setting has been successfully configured.
6
STH-03ZB User's Manual
7. Adding STH-03ZB to Receiving Device
You will need:
Sharp pointed tool
Coordinator or router device (WZB-01USBPS or WZB-02485RPS or WZB-01USBPSR or
WZB-05ETPS)
7.1. Ensure coordinator or router device is powered on (see relevant device’s manual).
7.2. Ensure batteries have been installed in STH-03ZB (see "
Installing and Replacing
Batteries in STH-03ZB"
section).
7.3. Use the sharp pointed tool to apply 1 quick press to link switch on the coordinator or router
device, the blue ZigBee LED should flash 1 flash per 0.5 second and repeat the sequence,
detection can take up to 30 seconds.
7.4. If 30 seconds has passed and no device has been connected, the blue ZigBee LED on the
coordinator or router should return to one flash then pause for a second and repeat the
sequence.
7.5. When STH-03ZB has been connected, the blue ZigBee LED on the coordinator or router
device should flash, it should return to one flash then pause for a second and repeat the
sequence.
7.6. If STH-03ZB has been successfully connected, the green status LED should flash every 60
seconds to confirm successful addition.
If STH-03ZB’s status LED does not flash once every 60 seconds, then it has not been connected
successfully. Repeat above steps until STH-03ZB has been connected successfully. If
STH-03ZB has still not been connected successfully after a few attempts, check it is within the
operational distance of 50m (line of sight) from the coordinator or router device and away from
other 2.4GHz devices that might interfere with its operation.
If STH-03ZB had been successfully connected, but is showing unable to find coordinator or
router device (repeating sequence of 2 flashes and pause for 2 seconds), then check coordinator
and all router (where applicable) devices are correctly powered on. If coordinator and all router
(where applicable) devices are functioning correctly, STH-03ZB may be out of range from the
coordinator or router device, an additional router may need to be added to extend the range.
7
STH-03ZB User's Manual
8. Removing STH-03ZB from Receiving Device
You will need:
Sharp pointed tool
8.1. Ensure coordinator or router device is powered on (see relevant device’s manual).
8.2. Ensure STH-03ZB is powered on (see
Installing and Replacing Batteries in STH-03ZB
section) and has already been connected to the coordinator or router device.
8.3. Use the sharp pointed tool to apply 2 quick presses to the link switch on the coordinator or
router device, the blue ZigBee LED should flash rapidly for up to 30 seconds or until removal
has been successful, removal need to take place within 30 seconds.
8.4. 3 quick presses to the link switch on STH-03ZB, the green status LED should flash rapidly
for up to 30 seconds or until removal has been successful.
8.5. If STH-03ZB has been successfully removed, coordinator or router device’s blue Zigbee
LED should flash once and pause for one second then repeat the sequence, STH-03ZB’s
green status LED should flash once per second.
Recommendation:
It is strongly recommended to remove batteries immediately from STH-03ZB
once it has been removed successfully from the coordinator or router device as this will greatly
improve battery life.
9. STH-03ZB LED Signal Status
The table below shows the LED signal status for STH-03ZB:
STH-03ZB LED
Status
Green LED:
1 flash per second (loop)
Ready to join
– ready to be connected to
coordinator or router
Green LED:
1 flash every 60 seconds (loop)
Successfully Connected
– connected and
functioning normally
Green LED:
Rapid flashing (continue)
Orphaned
– connected but unable to find
coordinator or router
Green LED:
Rapid flashing up to 30 seconds
Removing
– being removed from coordinator or
router
Green & Red LED:
ON for 3 seconds
ZigBee Reset
– Zigbee linkage to all data
receivers being reset
Red LED:
1 flash every 60 seconds (loop)
Low Power
– low battery power, replace
batteries immediately
8
STH-03ZB User's Manual
10. ZigBee Reset
In the case where the data receivers (coordinator or router devices) for the STH-03ZB are no
longer available or have been reset, to clear STH-03ZB ZigBee linkage to all data receivers,
apply 3-second press to the link switch,
the green and red status LEDs should be ON for 3
seconds, then return to just the green status LED flashing once every 1 second.
STH-03ZB’s ZigBee linkage to all data receivers has been cleared.
Recommendation:
It is strongly recommended to remove batteries immediately from STH-03ZB
once its linkage to data receivers has been removed successfully as this will greatly improve
battery life.
11. Product Specifications
Measurement Channel
Built-in 1 temperature and humidity sensor
Wireless Protocol l
Compliant IEEE 802.15.4, ZigBee2007/PRO
Operating Frequency
2.4GHz ISM Band
Transmission Range
50m (around 164 feet) Line of sight
RF Output Power
1mW/ 0dBm
Power Supply
3V 2 AA Alkaline battery
Operating Environment
-10~ +55 ºC, 85%RH. Max.
Power Consumption
TX:35mA Sleep:1.3uA
Measurement Accuracy
Tempe0.5 ºC/ Hu/-5%
Network Topology
Star/ Tree/ Mesh
Transmitting protocol
Modbus RTU
Addressing
IEEE MAC 64bit
Transmit Interval
1 second to 75 minutes setting by DIP Switch
Battery Life
1 year based on sending data per 5 minutes
Coordinator WZB-01USBPS / WZB-05ETPS
Peripherals
Router
WZB-01USBPSR / WZB-02485RPS
Dimensions
92(L) x 50(W) x 23(H) mm
Weight
86g
OS
Windows 95/ 98/ NT/ 2000/ XP/ Vista/ Win7
Certifications
CE/ FCC
