4.7 MONITOR SET
The function of monitor set is real time monitor of over current, over heat and freezing, on Home interface, short
press MONITOR SET to enter into monitor set interface as follows:
For configuration method and modification, please refer to Automatic Mode
(Energy Save Mode) Schedule:
After Mode: set the mode after the drying mode ends, can be configured through the proprietary attribute
ModeAfterDry (0x1007) of Thermostat Cluster (0x0201).
Duration: set how long the dry mode lasts, can be configured through the proprietary attribute DryTime
(0x1006) of Thermostat Cluster (0x0201), the configurable range is 5-100 minutes.
For example, in order to quickly dry the water on the floor of the bathroom, the device can be set to quickly heat
in a short time to dry the floor. Enter the configuration interface as follows:
4.6 Dry Mode Schedule
Remain: shows the remaining time of the drying mode
To enter into the setting interface and setting method, please refer to the 1.4
Auto Mode (Energy Save Mode) Schedule.
Start and end mean away time.
D means date, M means month, Y means year (2019-2099).
2.If away mode has already been activated, the values of end time for away mode are set as 0, the device will
always execute current set temperature with no time limitation. The device will consider the mode as anti-
freeze mode, the recommended temperature setting is 4-10
℃,
and
factory
default
setting
is
6
℃.
4.5 Away Mode Schedule
User can set time to leave home and time to go home according to the requirements of themselves, and set how
the device will control the temperature during this period.
1.If away mode has already been activated, the end time for away mode is valid, the device will execute Away
Mode Temperature Schedule before the end time.
Hysterersis (0.5°C by default)
To prevent the undulation of sensor temperature when the sensor temperature is approaching the set
temperature, which will cause that the controller may keep switching on/off the relay. Here hysterersis enables
the controller to control the relay only when the sensor temperature is a little bit lower than the set temperature,
this value can be set.
For instance, when hysterersis is set as 0.5 degree, then only when current sensor temperature is 0.5 degree
lower than the set temperature, will the controller heat, if the sensor temperature >= set temperature, the
controller will not heat.
This value can also be configured through the proprietary attribute Hysterersis (0x100A) of Thermostat Cluster
(0x0201).
Note: This hysterersis only valid when the control type is single sensor, please refer to the part Control Type.
reported to the associated devices, meanwhile the buzzer or vibrator will beep 3 times every 10 seconds. The
over heat alarm function can be disabled, which can be set directly through the device. Or can be configured
through the attribute AlarmAirTempOverValue (0x2001) of Thermostat Cluster (0x0201), when this value is set
as 0, this function is disabled.
Over heat alarm interface is as follow:
Note: to cancel over current alarm or over heat alarm, just press and hold
button
for over 3 seconds or reset power of the device. After cancel
manually, the relay will show heating forbidden icon
within 120
seconds, but other operations are allowed.
Max Current (16A by default)
If current is over the set value, the relay will be forced to off by the device, and the state will be reported to the
gateway. The over current alarm function can be disabled, which can be set directly through the device. Or can
be configured through the ACAlarmsMask and ACCurrentOverload of Electrical Measurement (0X0B04), for
details please refer to the configuration value .
RoomTemp alarm (
by default)
45°C
If room temperature is over the set value, the relay will be forced to off by the device, and over heat alarm will be
Short press button
to select the item would like to modify, then short press
move up and move down buttons to modify value of selected item, then
short press button
to save and quit, short pressing button
only quits
without saving.
F
Window Open Detect (disabled by default)
Once the device is powered on and stable, referring to the room temperature sensor, if the temperature
decreases to the threshold of this setting, the window open mark will be enabled, the relay will be forced to turn
off to save energy, then the icon will appear.
After window open mark is enabled, if the temperature increases to the threshold of this setting in 3 minutes,
the window open mark will be disabled.
Once the window open mark is enabled, it will be disabled after 10 minutes, and the device will keep current
working mode.
This value can also be configured through the proprietary attribute WindowOpenCheck (0x1009) of Thermostat
Cluster (0x0201), 0 means this function is disabled.
Note: this function will work better when the device is installed beside the window or door.
7:30,24
℃
~ 12:00,20
℃
18:00,16
℃
~ 22:30,18
℃
Saturday~Sunday
7:30,24
℃
~ 12:00,20
℃
18:00,18
℃
~ 22:30,18
℃
Short press button
to select the item would like to modify, then short
press move up and move down buttons
to modify value of selected
item, then short press button
to save and quit, short pressing button
only quits without saving.
4.9 OTHER SET
Select
OTHER SET on Home Interface to enter into OTHER SET interface as follow:
F
Short press button
to select the item would like to modify, then short
press move up and move down buttons
to modify value of selected
item, then short press button
to save and quit, short pressing button
only quits without saving.
F
4.8 TIME/DATE SET
Select TIME/DATE on Home Interface to enter into TIME/DATE SET interface as follow:
The device Time Cluster is client, if the bound device supports local time of Time Cluster, the device will
acquire local time from the bound device spontaneously under 3 situations: acquire after this device is added
to a network, acquire when the device already added to a network and power is reset, acquire every 24 hours .
