background image

WLB5254USB                                                                  User manual 

Page 18 of 18 

FCC Compliance Statement 

CAUTION: 

Any changes or modifications in construction of this device which 

are not expressly approved the party responsible for compliance could void 
the user's authority to operate the equipment.

 

 
NOTE: 

This equipment has been tested and found to comply with the limits for 

a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications, 
however, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or 
more of the following measures: 

 

-

 

Reorient or relocate the receiving antenna. 

-

 

Increase the separation between the equipment and receiver.

 

-

 

Connect the equipment into an outlet on a circuit different from that 
to which the receiver is connected.

 

-

 

Consult the dealer or an experienced radio/TV technician for help.

 

 

CE Mark Warning: 

 

This is Class B product. In a domestic environment, this product may cause 
radio interference, in which case the user may be required to take adequate 
measures. 
 

Summary of Contents for WLB5254USB



















Reviews: