background image

9

Instructions for user - CEX9-U - 801041 - November 2018 v1.00 Art.no:

 9120-25688

6. Operation

+

Reset 

1

Press + hold!

Reset completed

3

2

All factory settings can be recalled:
•  Press   and   simultaneously. The display now counts backwards from “

10

“ to 

00

“ in second intervals. The appliance is reset at value “

00

“ - if you stop pressing 

the keys earlier, you will cancel the process.

Reset to factory setting

Set the exact temperature you need on the appliance and open the hot water tap. 
Once you feel that the water is too hot, do not add any cold water and, instead, enter 
a lower temperature on the appliance. If you were to add cold water, the water already 
heated would cool down again and valuable energy would be wasted. Moreover, the 
cold water added in the tap is not covered by the control range of the electronic cir-
cuitry, with the result that temperature constancy is no longer guaranteed.

How to save energy

The symbol 

 shows that the appliance works in an energy saving mode (i.e. the 

momentary energy consumption is subject to the selected temperature and to the flow 
rate in the energy saving mode. 

 

Power limit

ECO mode

ECO mode

If the full output of the instantaneous water heater does not suffice to heat the tapped 
quantity of water, this will be indicated by 

 on the LCD (e.g. in winter time, when 

open ing several taps at once). When you reduce the hot water flow rate, 

 stops 

lighting because the output of the appliance is sufficient to reach the set temperature 
again.

Power limit

Unit provides no output

When operating with preheated water (e.g. with solar systems), ensure that the maxi-
mum inlet temperature is not exceed. 
If the inlet temperature exceeds the setpoint, the icon   on the digital display indi-
cates that the heating power is switched off. 

Top-up heating

Summary of Contents for CLAGE CEX9-U













Reviews: