background image

801314UK - G4 Boiling chilled commercial installation instructions - June 2016 -  V2.04 

Page 25 of 28

End of life disposal

The use of this crossed out wheeled bin logo indicates that this product needs to be disposed of 

separately to any other household waste.
Within each of the European Union member countries, provisions have been made for collection 

and recycling of unwanted electrical and electronic equipment. In order to help preserve our 

environment we ask that you dispose of this product correctly. Please contact Zip Customer 

Service on 0345 6 005 005 for advice.

Warranty

Certain warranties may be implied by law into your contract with Zip. The  warranty provided below is  

additional to these implied warranties and nothing set out below shall limit your statutory rights or rights at law.

Zip Heaters (UK) warrants that, should the hot tank fail within five years of installation subject to satisfactory 

maintenance and registration of the product, or any part fail within two years of installation, the part will be  

repaired or replaced free of charge by Zip, its distributor or service provider, (except as set out below),  

provided the appliance is installed and used strictly in accordance with the instructions supplied, and that 

failure is not due to accident, misuse, abuse, unsuitable water conditions, or to any alteration, modification or 

repair by any party not expressly nominated by Zip.

No costs are payable by the customer other than any mileage or travelling-time charges incurred by a Zip  

service provider or the cost of removal, cartage and re-installation of any component of the appliance if it 

needs to be returned for repair to Zip or its distributor.

This warranty does not cover damage resulting from non-operation of the appliance, the use of non authorised 

parts or consequential damage to any other goods, furnishings or property.

No warranty applies to the life of any filtration cartridge installed with the appliance as cartridge life may vary 

according to water quality and the rate of water consumption.

Zip does not exclude, restrict or modify any liability that cannot be excluded, restricted or modified or which 

cannot, except to a limited extent, be excluded, restricted or modified as between the owner or user and Zip 

under the laws applicable.

Furthermore this warranty does not displace any statutory warranty, but, to the extent to which Zip is entitled 

to do so, the liability of Zip under any statutory warranty will be limited at Zip’s option to the replacement of the 

appliance or supply of equivalent appliance, the payment of the cost of replacing the appliance or acquiring an 

equivalent appliance, or the payment of the cost of having the appliance repaired or the repair of the  

appliance.
HydroTap

®

G4 residential models are designed specifically for use in a domestic environment and 

inappropriate installations such as in a commercial location will invalidate the warranty.

Registering your purchase.
Registering your Zip installation on the Zip website may help to establish date of installation should it become 

necessary to service the appliance under terms of the Zip warranty. To register your installation go to  

www.zipwater.com/uk and look under the heading “Warranty”.

Summary of Contents for Classic HydroTap G4 range





























Reviews: