background image

05

Installation instructions & user manual 
804544UK V2.03 Oct 2018 - Zip Econoboil

Technical support  

Tel: 0345 6 005 005  Email: service@zipindustries.co.uk  www.zipwater.co.uk

!

!

Before installation

Before installation ensure that provision has been made for the 

following

• 

Review the technical specifications.

• 

Ensure the mounting wall can support the product weight when full of water 

(See Technical specification, page 6).

• 

Provide sufficient space to install the Econoboil and other components in 

accordance with these installation instructions.

•  Position the Econoboil so there is at least 150 mm clearance above it for 

service access, 65 mm to its left and 20 mm to its right – the tap nozzle is 

usually positioned nominally 360 mm above a draining board, drip tray or sink 

bowl area.

• 

For all Zip Econoboil models, user easy accessible 1 x 230V AC 13A socket or 

double pole isolation switch, (correctly rated for the appliance), is required. 

• 

The Econoboil  must be connected in accordance with IEE regulations. See 

Technical specification, page 6 for power ratings.

Note 

Check cable and plumbing against inlet /outlet  positions before proceeding.

• 

A wholesome (cat 1) water supply connection with isolation valve within 

reach of the Econoboil (and positioned so that the isolation valve will not be 

obstructed when the Econoboil is installed). 

•  Vent / outlet drainage to a draining board, drip tray or sink bowl area.
•  Access to drainage from a vent situated at the base of the Econoboil.

• 

A wholesome (cat 1) cold water supply with a minimum working pressure of:  

(see Technical specification, page 6 min. / max. water supply pressure).

• 

A 0.35 MPa (3.5 bar) pressure limiting valve supplied must be fitted if the   

incoming mains water pressure is likely to exceed 0.5 MPa (5.0 bar).

• 

The Econoboil must be placed with its base in a horizontal position.

IMPORTANT! 

 Do not proceed with the installation if these requirements are not 

met.

Summary of Contents for Econoboil 305542

















Reviews: