background image

Page 2 of 12 

Zip FlushMaster Pearl Installation & Maintenance Instructions - 82902 - January 2012 v1.00

You may need these accessories ( see page 3 for package contents).

Table of Contents 

Key Features ................................................. 3

Read These Warnings First ............................ 3

Check Your Package ...................................... 3

Installation Procedure .................................... 3

Set Up Water Discharge  ................................ 4

Install Sensor ................................................. 6

Connect Latching Valve Cable ........................ 7

Connect Optional Power Pack ........................ 8

Set Flush Timing ............................................ 8

Completing Installation .................................. 9

Maintenance Instructions ............................... 10

Problem Solving............................................. 11

Contact Details .............................................. 12

99168 Pearl Water Saver Sensor only (64mm body)

99021 Zip FlushMaster Cistern Autosyphon 1.00 inch BSP/ 25 mm
99022 Zip FlushMaster Cistern Autosyphon 1.25 inch BSP/ 32 mm
99023 Zip FlushMaster Cistern Autosyphon 1.50 inch BSP/ 38 mm

99024 Zip FlushMaster Direct Injection Airbreak 1.00 inch BSP / 25 mm
99025 Zip FlushMaster Direct Injection Airbreak 1.25 inch BSP/ 32 mm
99026 Zip FlushMaster Direct Injection Airbreak 1.50 inch BSP/ 38 mm

Fixing 
bracket 

99031 Zip FlushMaster AC Power Pack

Accessories

99039 -Restrictaflow

41092 Mk 2 Retrofit Sensor DC (105mm body) WS006 ( Valve assy not included )
41093 Mk 2 Retrofit Sensor AC (105mm body) WS007 ( Valve assy not included )

Summary of Contents for FlushMaster Pearl













Reviews: