background image

Page 20 of 24   

802698 - G4  User Guide - June 2015 - v2.00

  

 Filter Maintenance

To change the Filter: 

(See also Section C)

1. 

Open the door of the under sink unit.

2. 

Relieve system pressure via the filter flush stop cock, a quick open and 
close will do. Use the bucket to catch the discharge.

3. 

Grasp filter cartridge, depress the red lever at the top right of the filter and 
rotate the cartridge a quarter turn to the left, then gently pull down. 

4. 

Caution: 

 a small amount of water will drip as the cartridge is removed.

5. 

Do not tilt the cartridge as water may spill from it if tilted.

6. 

Unpack  replacement  cartridge  and  remove  sanitary  cap,  write  today’s 
date where shown on the label. 

7. 

Avoid  touching  the  filter  O-rings  and  filter  opening  as  this  may  cause 
bacterial contamination of the cartridge.

8. 

Moisten the O-rings with water, align the front cartridge label to the left (as 
shown  in  the  “insert  filter”  diagram  for  filter  cartridge  replacement),  and 
push the new cartridge into the filter head. 

9. 

Turn  the  cartridge  a  quarter  turn  to  the  right  until  the  cartridge  comes 
to  complete  stop  and  is  locked  into  position,  with  the  front  label  facing 
forward.  

10. 

Initiate the filter flush programme by scrolling through the menu screen 
(See section C).

11. 

When completed, wipe up any spills and dispose of spent filter cartridge 
and packaging thoughtfully.

12. 

Close the door to secure the appliance.

13. 

Adjust the filter settings in Section G - filter - Litres and Days used. 

The Zip HydroTap notifies when a filter replacement is due. If you notice one 
of the following, you will need to change the filter: 

•  The Change Filter light will flash until reset. (See Section C)

•  The filter percentage will change to 0% on the screen. 

NOTE:

 Depending on local water quality conditions and usage, the filter may 

require changing anywhere from 500 Litres to 10000 Litres. You may also 
need to replace the filter if you notice unpleasant odours or tastes.

Some water may drip from the filter head (socket) during replacement. Keep 
a towel handy to dry up any drips.

Summary of Contents for HydroTap G4 Celsius Series

























Reviews: