Zip Soap Dispenser Installation & Operating Instructions 87400 - July 2007
Page 3
A. Service Instructions
1. Open the upper cover using the key provided. (The security
wrench for battery box is attached in the upper cover.)
2. Remove cover from battery box, put 6 pcs of Alkaline AA
1.5V batteries into the battery box, put box back into original
casing and close with cover. (Fig. 7)
3. Remove soap tank, open it and pour liquid soap into the
container. Close properly. Should any soap spill over the
outside of the container, it must be cleaned thoroughly.
Replace clean soap container in its original position. Close
the casing and lock it.
4. Place your hands under the dispenser. The LED will turn on
and the dispenser will release a portion of liquid soap.
5. When using for the first time, repeat that process a few
times to order to fill the system.
6. A flashing LED will indicate low battery. Replace
batteries with new ones. If problem persists, contact
your dealer.
-The sensing range is automatically self-
adjusting.
-Dispenser will detect the incoming object and
adjust the sensing range dynamically.
-Drop volume setup: (Fig. 10)
1. Push 1st time to enter setup mode (See LED
flash)
2. Push 2nd time to start counting (See LED light)
3. Push 3rd time to stop setup mode (See LED off)
1. Check if soap dispenser is firmly fixed to
the wall.
2. Check if soap container cover is closed
properly and no soap is leaking.
3. Use 6 pieces of new Alkaline AA (1.5V)
batteries. Ensure that the batteries are
installed properly and in the right direction
(o/- indication).
4. Once batteries are installed and casing is
closed, a red light will flash 4 times to
indicate normal function.
5. Make sure soap dispenser is locked
properly using the key provided.
6. Ensure that the battery cover is secured
with battery security screw.
6. OPERATION INSTRUCTIONS :
8. SENSING RANGE AND SOAP VOLUME
ADJUSTMENT:
7. INSTALLATION CHECK :
11. TROUBLE SHOOTING (FOR QUALIFIED ELECTRICIAN USE ONLY) :
Fig. 10
SOAP VOLUME
ADJUSTMENT
BUTTON
1. Ensure no light source is aimed at the sensor from
below.
2. Use a pure liquid soap only and clean the soap
container properly before each re-fill. Deposits of old
soap will lead to malfunction and jamming.
3. Do not dilute liquid soap and do not use grain
containing soap. Observe specified viscosity factor of
liquid soap.
4. Do not immerse the soap dispenser in water or clean
it under running water. This will lead to short circuit.
5. Should the dispenser be out of order and batteries
have been replaced, do not attempt any repair work.
Call your dealer for professional assistance.
9. IMPORTANT NOTICE :
Problem
Solution
LED does not indicate
- Check batteries and ensure that they are new and properly inserted.
- Check sensor cover for stain. Clean unit properly.
LED flashes when unit is not used
- Low voltage: Change batteries (Fig. 7)
- Sensor is activated constantly. Remove the object below the sensor.
- If above does not help, contact your dealer for professional assistance.
No soap discharges when motor works
- Obstructed soap dispenser nozzle. Clean soap container or change it.
- Check if soap is not liquid enough (viscosity as per specification).
Insufficient soap is released
- Soap has hardened: use unit fro several times or remove soap container and wash it thoroughly.
- Soap nozzle is obstructed: wash soap container and use unit continuously until normal soap
quantity is dispensed.
B. Users Instructions
1. Put palm of your hand under the dispenser. The
sensor will activate and the motor will release
1ml of liquid soap. If you need more soap, repeat
the movement a few times, waiting at least 1
second before you replace your hand under the
unit. Do not scoop soap from the nozzle as this
may lead to damage. (Fig. 8)
2. To safeguard the sensitive electrical components
inside the dispenser, always remove the soap
tank completely from housing during re-fill.
NEVER attempt to fill when the soap tank is still in
the dispenser housing unit. (Fig. 9)
For all other enquiries call you local deal for technical assistance.
AA (1.5V)
Fig. 9
AA x 6
Fig. 7
Fig. 8
Notice: Should the dispenser be out of order and batteries have been replaced,
do not attempt any repair work. Call your dealer for professional assistance.
Stage 1: LED flashing indicate battery is low and
sensing function is still working.
Stage 2: LED always lights up and without sensing
function. Battery is nearly exhausted.
10. BATTERY LOW INDICATION :
Caution:
Placing of the batteries in an
incorrect Position may cause a malfunction.
