background image

SAFETY 

ZIPPER MASCHINEN GmbH     www.Zipper-Maschinen.at



24   

ZI-HEK40V-AKKU 

 

Ensure that the cutter does not touch the ground or other objects. 

 

Wait until the electric power tool has come to a standstill before putting it down. 

 

When interrupting work, never leave the machine unattended and keep it in a safe place. 

 

Always switch the machine off before transporting it to other workplaces. 

 

Never grasp the blade of the machine. 

 

Ensure that all guards and handles are fitted before using the machine. Never attempt to switch on 
an incompletely assembled machine or a machine which has unauthorised modifications. 

 

Operate the machine only in the technical condition stipulated and delivered by the manufacturer. 
Unauthorised changes to the machine exclude liability of the manufacturer for any resulting 
damage and/or injury. 

 
Safety instructions for the battery charger: 

 

Keep the battery charger away from rain or moisture. Penetration of water in the battery charger 
increases the risk of an electric shock. 

 

Keep the battery charger clean. Contamination can lead to danger of an electric shock. 

 

Before each use, check the battery charger, cable and plug. If damage is detected, do not use the 
battery charger. Never open the battery charger yourself. Have repairs performed only by a 
qualified technician and only using original spare parts. Damaged battery chargers, cables and 
plugs increase the risk of an electric shock. 

 

Do not place any objects on the battery charger and do not place the battery charger on soft 
surfaces. There is a risk of fire. 

 

Always check that the mains voltage matches the voltage indicated on the rating plate of the 
battery charger. 

 

Never use the charger if cable, plug or the machine itself has been damaged by external 
influences. Take the charger to the nearest service centre. 

 

Never open the battery charger. If the battery charger is defective, take it to a service centre. 

 
Safety instructions for Li-ion batteries: 

 

Do not open the battery. There is a risk of a short-circuit. 

 

Protect the battery from heat, e.g. from continuous exposure to sunlight, fire, water and humidity. 
There is a risk of explosion. 

 

In case of damage and improper use of the battery, vapours may be emitted. Ventilate the area 
and seek medical help in case of complaints. The vapours can irritate the respiratory system. 

 

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact 
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid 
ejected from the battery may cause irritation or burns. 

 

Use only original batteries with the voltage indicated on the rating plate of your electric power tool. 
If other batteries are used, e.g. imitations, reconditioned batteries or third-party products, there is 
a risk of injuries as well as damage caused by exploding batteries. 

 

The battery voltage must match the battery charging voltage of the battery charger. Otherwise 
there is a risk of fire and explosion. 

 

Recharge only with the charger specified by the manufacturer. A charger that is suitable for one 
type of battery pack may create a risk of fire when used with another battery pack. 

 

Pointed objects, such as nails or screwdrivers, or external forces may damage the battery. This 
may cause an internal short-circuit and the battery to burn, smoke, explode or overheat. For 
disposal, transport or storage, the battery must (plastic bag, box) or the contacts are packed must 
be taped. 

 

 

Autogoods “130”

130.com.ua

Summary of Contents for ZI-HEK40V-AKKU







































Reviews: