MAINTENANCE
ZIPPER MASCHINEN GmbH www.Zipper-Maschinen.at
33
ZI-STE2000IV
To ensure the engine to work in good order, the clearance of the spark plug must be correct, and
has no accumulated charcoal.
1.
Dismantle the repair cover of the spark
plug (Fig. Z).
2.
Dismantle the cap of the spark plug.
3.
Clean out the filth around the base of the
spark plug.
4.
Dismantle the spark plug with a spanner.
B – Hold of the handle (Fig. AA)
C – Banner of the spark plug (Fig. AA)
D – Cap of the spark plug (Fig. AA)
5.
Examine the spark plug with your naked eyes. If the insulator has crazed or has fragments,
you should discard the spark plug. If the old spark plug needs to be used continually, you
must clean it up with a brush.
6.
Measure the clearance of the spark plug with a gauge. The clearance should be 0.6nm to
0.7nm. (Fig. AB)
7.
Install the spark plug carefully by hand. Pay attention not to overlap the screw thread.
8.
After installing a new spark plug by hand, screw it with a spanner for a half circle in order to
press the washer tightly. If an old spark plug is installed, you only need to screw it from one
eighth circle to one fourth circle after it is fixed.
9.
Re-install the cap of the spark plug.
11.2
Transport / Storage
In order to avoid the generator leaking oil during transport or temporary storage, make sure to
switch off the generator, keeping it at a standing pose under normal operations. After the engine
is totally cooled, turn the ventilating pole of the fuel-filling lid to the “close” position thoroughly.
When transporting the generator:
Do not let the fuel spill out of the fuel tank. (The top of the fuel-filling tank should have no
fuel.)
When the generator is placed on vehicle, do not run the engine. You should take the
generator down from the car and operate it in the draught.
When you take the generator to the car, avoid exposing it to sunshine. If it is put in sealed
carriage for a long time, the high temperature of the carriage may cause the fuel to boiling
away, thus leads to burn.
Before the generator is put into a long-time storage, you should:
Make sure the storage area is clean and dry.
Pull 1-2 x per year starter cable. (Fig. AD)
1.
Discharge the machine oil.
2.
Dismantle the spark plug, and pour a big spoon of clean machine oil into the engine. Make the
engine rotate for several circles to make the oil evenly distribute. Install the spark plug again.
3.
Pull the starting hold (Fig. AD) slowly until you feel the resistance. At this time, the piston
reaches the compressed stroke, and both the entering and the discharging valve are closed. To
store the generator under such condition will help to prevent the inside of the machine rusting.
11.3
Disposal
Do not dispose of the ZI-STE2000IV in residual waste. Contact your local authorities
for information regarding the available disposal options. When you buy at your local
dealer for a replacement unit, the latter is obliged to exchange your old
A T T E N T I O N
The spark plug must be fixed
firmly, or else it will become
very hot and damage the
generator.
Do not use the spark plug whose
thermal measurement range is not
suitable.
Summary of Contents for ZI-STE2000IV
Page 10: ...TECHNIK TECHNIC TEHNIKA ZIPPER MASCHINEN GmbH www Zipper Maschinen at 10 ZI STE2000IV B A...
Page 11: ...TECHNIK TECHNIC TEHNIKA ZIPPER MASCHINEN GmbH www Zipper Maschinen at 11 ZI STE2000IV 2 A 1 2...
Page 98: ...PRODUKTBEOBACHTUNG ZIPPER MASCHINEN GmbH www Zipper Maschinen at 98 ZI STE2000IV...
