background image

  SAFETY 

  

ZIPPER MASCHINEN GmbH     

www.zipper-maschinen.at

     

21   

ZI-BHS2600 

11

 

SAFETY 

This section contains information and important notes on the safe commissioning and handling of the ma-

chine. 

 

For your safety, read this manual carefully before commissioning. This will enable you to han-

dle the machine safely and thus prevent misunderstandings as well as personal injury and 

damage to property. Pay special attention to the symbols and pictograms used on the ma-

chine as well as the safety information and danger warnings! 

 

11.1

 

Intended use of the machine 

The machine is intended exclusively for the following activities:  

For cutting shrubs, bushes, bushes and hedges within the specified technical limits. 

N OTE

 

 

ZIPPER MASCHINEN assumes no responsibility or warranty for any other use or use be-

yond this and for any resulting damage to property or injury.

 

 

11.1.1

 

Technical restrictions 

The machine is designed for the work under the following conditions: 

Relative humidity: 

max. 90 % 

Temperature (for operation): 

+5° C to +40° C 

Temperature (Storage, Transport): 

-20° C to +55° C 

11.1.2

 

Prohibited applications / Dangerous misuse 

 

Operating the machine without adequate physical and mental fitness. 

 

Operating the machine without knowledge of the manual. 

 

Modifying the machine design. 

 

Operating the machine outside the technical limits specified in this manual. 

 

Removing of the safety markings attached to the machine. 

 

Modifying, circumventing or disabling the safety devices of the machine. 

 

Operating the machine in rainy conditions. 

 

Operating the machine indoors or in closed areas. 

 

Operating the machine in a potentially explosive environment. 

 

The non-intended use or the disregard of the explanations and instructions described in this manual will 

result in the expiration  of all warranty claims and compensation claims for damages against ZIPPER 

MASCHINEN GmbH. 

11.2

 

User Requirements 

The machine is designed to be operated by one person. The prerequisites for operating the machine are 

physical and mental fitness as well as knowledge and understanding of the operating instructions. Persons 

who, due to their physical, sensory or mental capabilities, inexperience or lack of knowledge, are unable to 

operate the machine safely must not use the machine without supervision or instruction by a responsible 

person. 

Please note that locally applicable laws and regulations determine the minimum age of the operator and 

may restrict the use of this machine! 

Summary of Contents for ZI-BHS2600








































Reviews: