background image

127899 Rev. A

5

Z I PP I E   Z M- 3 1 0

IV. NOTICE– READ BEFORE USE

A. CHOOSE THE RIGHT CHAIR & SAFETY
OPTIONS

Sunrise provides a choice of many power wheelchair styles, sizes and
adjustments to meet the needs of the user. However, final selection
of a wheelchair rests solely with you and your health care profes-
sional. Choosing the best chair for you depends on such things as: 

1. Your size, disability, strength, balance and coordination. 
2. Your intended use, and your level of activity.
3. The types of hazards you must overcome in daily use (in

areas where you are likely to use your chair). 

4. The need for options for your safety and comfort (such as

positioning belts or special seat systems). 

INTENDED USE: The ZM-310 is a battery operated device with
wheels that is intended for medical purposes to provide mobility
to persons restricted to a sitting position. 

B. ADJUST CHAIR TO YOUR ABILITY 

You need to work with your doctor, nurse or therapist, and your
supplier, to fit this chair and adjust the controller settings for your
level of function and ability.

C. REVIEW THIS MANUAL OFTEN 

Before using this chair you, and each person who may assist you,
should read this entire Manual and make sure to follow all instruc-
tions. Review the warnings often, until they are second nature to you.

D. WARNINGS 

The word “WARNING” refers to a hazard or unsafe practice that
may cause severe injury or death to you or to other persons. The
“Warnings” are in four main sections, as follows:

1. V — EMI

Here you will learn about electromagnetic interference and
how it can affect your chair.

2. VI — GENERAL WARNINGS 

Here you will find a safety checklist and a summary of risks
you need to be aware of before you ride this chair. 

3. VII — WARNINGS — COMPONENTS & OPTIONS 

Here you will learn about your chair. Consult your supplier
and your health care professional to help you choose the
best set-up and options for your safety. 

4. X — BATTERIES

Here you will learn about battery and charger safety, and
how to avoid injury. 

Throughout this owner’s manual and on the wheelchair you will
see the icons listed below to identify warnings and potential haz-
ards.

WARNING!

These warnings must be followed, failure to
do so may cause personal injury or may dam-
age the wheelchair.

ESD:

Electrostatic Discharge can damage printed
circuit boards.

V. EMI (ELECTROMAGNETIC INTERFERENCE)

WARNING

Heed all warnings to reduce the risk of unintended brake release
or chair movement:

1. Beware of the danger from hand-held transceivers. Never

turn on or use a hand-held transceiver while power to your
chair is on. Use extra care if you believe that such a device
may be in use near your chair.

2. Be aware of nearby radio or TV stations, and avoid coming

close to them. 

3. If unintended movement occurs, turn your chair off as soon

as it is safe to do so.

A. WHAT IS EMI?

WARNING

1. EMI means: electromagnetic (EM) interference (I). EMI comes

from radio wave sources such as radio transmitters and
transceivers. (A “transceiver” is a device that both sends and
receives radio wave signals). 

2. There are a number of sources of intense EMI in your daily

environment. Some of these are obvious and easy to avoid.
Others are not, and you may not be able to avoid them. 

3. Powered wheelchairs may be susceptible to electromagnetic

interference (EMI) emitted from sources such as radio sta-
tions, TV stations, amateur radio (HAM) transmitters, two
way radios, and cellular phones.

4. EMI can also be produced by conducted sources or electro-

static discharge (ESD).

B. WHAT EFFECT CAN EMI HAVE?

WARNING

1. EMI can cause your chair, without warning, to: 

• Release its brakes
• Move by itself
• Move in unintended directions
If any of these occur, it could result in severe injury to you
or others. 

2. EMI can damage the control system of your chair. This could

create a safety hazard, and lead to costly repairs.

C. SOURCES OF EMI

WARNING

The sources of EMI fall into three broad types: 

1. Hand-Held Transceivers: 

The antenna is usually mounted directly on the unit. These include:

Citizens band (CB) radios

“Walkie-talkies” 

Security, fire and police radios 

Mobile phones

Lap-top computers with phone or fax 

Other personal communication devices 

Electronic  Article Surveillance Systems  

NOTE– These devices can transmit signals while they are on, even if not in

use. 

Summary of Contents for ZM-310

































Reviews: