40
EN
TROUBLESHOOTING
CAUTION! Opening the housing of the device without a prior contact with a
manufacturer’s
service
voids the warranty.
If you suspect a failure that requires the housing to be opened, contact manufacturer’s
service.
Error description
Possible causes
Solution
-----
Safety key issue
The safety key is not connected.
Connect the safety key correctly.
The computer is damaged.
Contact manufacturer's service.
E01
The computer does not
work
The computer is incorrectly
connected.
Verify the connection of computer cables.
The signal cable is broken or
insulation is worn
Verify plug connections. If it is correct and
the problem persists, contact the
customer service of the
manufacturer’s
service.
The computer is damaged
Contact the
manufacturer’s
service.
The connection between the
control board and the computer is
blocked
Contact the
manufacturer’s
service.
E02
The motor does not
operate
Incorrect supply voltage
Make sure the voltage is correct. If the
problem persists, contact the customer
service of the
manufacturer’s
service.
Incorrect connection of the motor
cable
Disconnect the cable and connect it again.
If the problem persists, contact
manufacturer’s service.
The controller is damaged
Contact the
manufacturer’s
service.
E03
The computer failed to
detect speed sensor
signal for 15 seconds
Sensor connection incorrect
Contact the
manufacturer’s
service.
Sensor plug connection incorrect
Verify plug connections. If it is correct and
the problem persists, contact
manufacturer’s service.
Sensor failure
Contact manufacturer’s service.
E04
Communication error
Incorrect connection or damage to
the wires.
Contact manufacturer’s service.
E05
Overload error
Motor failure
Make sure the motor has not burnt out. If
not, disconnect the treadmill from the
mains and reconnect it. If the problem
persists, contact manufacturer’s service.
Too low rated current in the
controller.
Replace the controller. Contact the
manufacturer’s
service.
Current exceeds the rated value
Make sure the weight of the user does not
exceed the maximum value for the device.
E06
Explosion-Proof
Protection. Incorrect
power supply
Supply voltage too low
Connect the device to the correct voltage.
Short circuit
Contact manufacturer’s service.
Summary of Contents for Dream GOLD
