32
Assembly Instructions
Unfold the Baby Stroller
• Take the stroller out of the package as shown in Fig. 1a
• Unfold the folding hook, pull the handlebar and gradually push to
open the stroller until a „click“ sound is heard as shown in
Fig. Ib and 1c
Install the Front Wheels
As shown in Fig. 2, attach each wheel to
the front wheel axle till a “click”
sound is heard.
Install the Rear wheel
As shown in Fig. 3, insert the rear wheels
into the rear wheel axle till a „click“ sound
is heard and ensure the rear wheels are
locked and cannot be pulled out.
1а
1b
1c
3
2
Folding Hook
13
Assembly Instructions
Unfold the Baby Stroller
• Take the stroller out of the package as shown in Fig. 1a
• Unfold the folding hook, pull the handlebar and gradually push to
open the stroller until a „click“ sound is heard as shown in
Fig. Ib and 1c
Install the Front Wheels
As shown in Fig. 2, attach each wheel to
the front wheel axle till a “click”
sound is heard.
Install the Rear wheel
As shown in Fig. 3, insert the rear wheels
into the rear wheel axle till a „click“ sound
is heard and ensure the rear wheels are
locked and cannot be pulled out.
1а
1b
1c
3
2
Folding Hook
13
• Un harnais de sécurité à 5 points est fourni pour retenir votre enfant et doit toujours
être porté.
• Pour l’attacher, poussez les clips latéraux (g) dans la boucle centrale (h). Des dispositifs
de réglage coulissants (i) sont installés et doivent être ajustés pour convenir à votre
enfant.
• Pour les détacher, appuyez sur les clips coulissants aux points U) et retirez la boucle.
AVERTISSEMENT ! Votre enfant doit être bien attaché et surveillé à tout moment.
• Démontage (pour le nettoyage) et remontage du harnais : pour le démonter, passez
les fixations de la sangle d’épaule (1) dans les fentes horizontales du dossier. Faites
passer les fixations de la sangle de taille (2) dans les fentes verticales du dossier. Faites
passer le dispositif de retenue de la sangle d’entrejambe (3) dans la fente de la base du
siège.
• Pour remettre le harnais en place, inversez le processus ci-dessus et vérifiez que toutes
les sangles sont bien fixées.
Harnais
6
7
A 5-point safety harness is provided to restrain your child and should always
be worn.
To fasten, push the side clips (g) into the centre buckle (h). Sliding adjusters (i)
are fitted and should be adjusted to suit your child.
To release, press the slide clips at points (j) and remove buckle.
WARNING!
Your child should be harnessed snugly and attended at all
times.
g
h
i
j
1
3
2
Harness removal (for cleaning) & re-fitting: to remove - pass the shoulder strap
retainers (1) through the horizontal slots in the backrest. Pass the waist strap
retainers (2) through the vertical slots on the backrest. Pass the crotch strap
retainer (3) through the slot on the seat base.
To re-fit harness, reverse the above process and check all straps are secure before
using the highchair.
The tray can be stored on the rear of the highchair. Remove tray (Step 6).
With the top of the tray facing outwards, attach the edge of the tray into the
allocated plastic clips located on the rear of the highchair seat unit. Ensure the
tray edge fits between both clips.
6
7
A 5-point safety harness is provided to restrain your child and should always
be worn.
To fasten, push the side clips (g) into the centre buckle (h). Sliding adjusters (i)
are fitted and should be adjusted to suit your child.
To release, press the slide clips at points (j) and remove buckle.
WARNING!
Your child should be harnessed snugly and attended at all
times.
g
h
i
j
1
3
2
Harness removal (for cleaning) & re-fitting: to remove - pass the shoulder strap
retainers (1) through the horizontal slots in the backrest. Pass the waist strap
retainers (2) through the vertical slots on the backrest. Pass the crotch strap
retainer (3) through the slot on the seat base.
To re-fit harness, reverse the above process and check all straps are secure before
using the highchair.
The tray can be stored on the rear of the highchair. Remove tray (Step 6).
With the top of the tray facing outwards, attach the edge of the tray into the
allocated plastic clips located on the rear of the highchair seat unit. Ensure the
tray edge fits between both clips.
Summary of Contents for MARS
Page 93: ......
