46
Assembly Instructions
Unfold the Baby Stroller
• Take the stroller out of the package as shown in Fig. 1a
• Unfold the folding hook, pull the handlebar and gradually push to
open the stroller until a „click“ sound is heard as shown in
Fig. Ib and 1c
Install the Front Wheels
As shown in Fig. 2, attach each wheel to
the front wheel axle till a “click”
sound is heard.
Install the Rear wheel
As shown in Fig. 3, insert the rear wheels
into the rear wheel axle till a „click“ sound
is heard and ensure the rear wheels are
locked and cannot be pulled out.
1а
1b
1c
3
2
Folding Hook
13
Assembly Instructions
Unfold the Baby Stroller
• Take the stroller out of the package as shown in Fig. 1a
• Unfold the folding hook, pull the handlebar and gradually push to
open the stroller until a „click“ sound is heard as shown in
Fig. Ib and 1c
Install the Front Wheels
As shown in Fig. 2, attach each wheel to
the front wheel axle till a “click”
sound is heard.
Install the Rear wheel
As shown in Fig. 3, insert the rear wheels
into the rear wheel axle till a „click“ sound
is heard and ensure the rear wheels are
locked and cannot be pulled out.
1а
1b
1c
3
2
Folding Hook
13
1. Fissare il poggiapiedi (F) al supporto del poggiapiedi (E). Inserire i pioli del
poggiapiedi nei fori predisposti sul supporto del poggiapiedi. Far scorrere il
poggiapiedi verso destra per bloccarlo in posizione.
Per rimuoverlo, far scorrere il poggiapiedi verso sinistra e allontanarlo dal supporto del
poggiapiedi.
2. Prendere due piedini superiori (C) e farli scorrere attraverso i fori assegnati nel
poggiapiedi assemblato.
Montaggio
1.
Attach the footrest (F) to the footrest support (E). Insert the footrest pegs
into holes allocated on the footrest support. Slide footrest to the right to lock
into position.
To remove, slide footrest to the left and pull away from footrest support.
10
3
E
F
2.
Take two upper legs (C) and slide them through the allocated holes in the
assembled footrest.
C
Your highchair converts to a junior chair.
To adjust the leg height, remove the lower legs. Press in the metal spring pin
located at the bottom of the upper leg and pull lower leg away.
Repeat for all 4 lower legs.
WARNING! Do not adjust the height when child is in the seat.
HIGHCHAIR
JUNIOR CHAIR
footrest peg
spring pin
1.
Attach the footrest (F) to the footrest support (E). Insert the footrest pegs
into holes allocated on the footrest support. Slide footrest to the right to lock
into position.
To remove, slide footrest to the left and pull away from footrest support.
10
3
E
F
2.
Take two upper legs (C) and slide them through the allocated holes in the
assembled footrest.
C
Your highchair converts to a junior chair.
To adjust the leg height, remove the lower legs. Press in the metal spring pin
located at the bottom of the upper leg and pull lower leg away.
Repeat for all 4 lower legs.
WARNING! Do not adjust the height when child is in the seat.
HIGHCHAIR
JUNIOR CHAIR
footrest peg
spring pin
Perno del poggiapiedi
Cliccare
47
Assembly Instructions
Unfold the Baby Stroller
• Take the stroller out of the package as shown in Fig. 1a
• Unfold the folding hook, pull the handlebar and gradually push to
open the stroller until a „click“ sound is heard as shown in
Fig. Ib and 1c
Install the Front Wheels
As shown in Fig. 2, attach each wheel to
the front wheel axle till a “click”
sound is heard.
Install the Rear wheel
As shown in Fig. 3, insert the rear wheels
into the rear wheel axle till a „click“ sound
is heard and ensure the rear wheels are
locked and cannot be pulled out.
1а
1b
1c
3
2
Folding Hook
13
Assembly Instructions
Unfold the Baby Stroller
• Take the stroller out of the package as shown in Fig. 1a
• Unfold the folding hook, pull the handlebar and gradually push to
open the stroller until a „click“ sound is heard as shown in
Fig. Ib and 1c
Install the Front Wheels
As shown in Fig. 2, attach each wheel to
the front wheel axle till a “click”
sound is heard.
Install the Rear wheel
As shown in Fig. 3, insert the rear wheels
into the rear wheel axle till a „click“ sound
is heard and ensure the rear wheels are
locked and cannot be pulled out.
1а
1b
1c
3
2
Folding Hook
13
3. Sulla parte superiore di ogni gamba superiore si trova un perno metallico a molla.
Premere questo perno e inserire le gambe superiori nei fori assegnati situati sotto
l’unità del sedile (A). Il perno apparirà attraverso il foro corrispondente dell’unità del
sedile quando sarà bloccato in posizione.
Ripetere per tutte e 4 le gambe superiori (comprese le due montate sul poggiapiedi).
4. Nella parte inferiore di ogni gamba superiore si trova un perno metallico a molla.
Premere questo perno e fissare le gambe inferiori (D) alla parte inferiore delle gambe
superiori. Il perno apparirà attraverso il foro corrispondente quando sarà bloccato in
posizione. Ripetere per tutte e 4 le gambe inferiori.
Montaggio
4
9
3
4
Your highchair has 2 adjustable tray positions.
To adjust the tray, press in the release clip located underneath the tray and pull
upwards to remove. Re-attach the tray in your preferred position. Insert the hooks
into the preferred slots on the seat unit arms. Rotate tray down and press firmly
into position. The tray will click once secure.
1
2
CLICK
3.
Located on the top of each upper leg is a metal spring pin.
Press in this pin
and
insert upper legs into the allocated holes located underneath the seat unit
(A). The pin will appear through the seat unit corresponding hole when locked
into position.
Repeat for all 4 upper legs (including the two assembled to footrest).
A
C
4.
Located on the bottom of each upper leg is a metal spring pin.
Press in this
pin and
attach lower legs (D) onto the bottom of the upper legs. The pin
will appear through the corresponding hole when locked into position.
Repeat for all 4 lower legs.
D
spring pin
spring pin
4
9
3
4
Your highchair has 2 adjustable tray positions.
To adjust the tray, press in the release clip located underneath the tray and pull
upwards to remove. Re-attach the tray in your preferred position. Insert the hooks
into the preferred slots on the seat unit arms. Rotate tray down and press firmly
into position. The tray will click once secure.
1
2
CLICK
3.
Located on the top of each upper leg is a metal spring pin.
Press in this pin
and
insert upper legs into the allocated holes located underneath the seat unit
(A). The pin will appear through the seat unit corresponding hole when locked
into position.
Repeat for all 4 upper legs (including the two assembled to footrest).
A
C
4.
Located on the bottom of each upper leg is a metal spring pin.
Press in this
pin and
attach lower legs (D) onto the bottom of the upper legs. The pin
will appear through the corresponding hole when locked into position.
Repeat for all 4 lower legs.
D
spring pin
spring pin
Perno a molla
Perno a molla
Cliccare
Cliccare
Summary of Contents for MARS
Page 93: ......
