background image

ZKS Group Company Limit 

 

-------------------------------------------------------------------------------------------------------------------------------------------------------------------------

ZKS Group Company Limited 

Address: No 552 Dong Zhou Road, Shanghai China 

TEL: +86-21-67679389 FAX: +86-21-67679336 

www.zksgroup.com 

19

Press  the  fingerprint, 
green and red light shine 
alternately 

Door has anti-lockup, 
only admin can open 
the door 

Cancel anti-lock setting 

Press  valid  fingerprint, 
LCD  show  red  light  5 
times  at  every  second 
alternately,  sensor  light 
also turn off.   

Lockup  5  minutes 
automatically if failed 
to identify fingerprint 
for 5 times   

Waiting  for  enough  time  to 
make  the  lock  exit  to  lockup 
status 

Identify  fingerprint  to 
open  the  door,  green 
and  red  light  shine 
alternately   

Lower battery voltage 
prompt 

Change new battery at once 

Can”t add fingerprint 

1.  First  authenticated 

users  doesn”t  have 

administrative 

privileges. 

2.Fingerprint capacity 
has reached. 

1.  Input  valid  fingerprint  with 

administrative privileges.   

2.Clear 

some 

useless 

fingerprints.   

Always  failed  to  identify 
fingerprint 

1.Finger too dirty 
2.Finger too dry 
3.Finger too wet 
4.Too dirty sensor 
5.Too strong light 
6. Put finger wrongly 

1.Clean finger 
2.Moist finger   
3.Wipe finger   
4.Clean sensor window 
5.Move or resist strong light   
6.Use  correct  way  to  press 

fingerprint   

 

 

Summary of Contents for ZKS-MW1





















Reviews: