ZKTeco BG2000 Series User Manual Download

Page: 3 / 34

BG2000 Series Barrier Gate (APP Version)

User Manual

P a g e

| 2

with, or relating to the use of the information contained in or referenced by this manual, even if ZKTeco

has been advised of the possibility of such damages.

This manual and the information contained therein may include technical, other inaccuracies or

typographical errors. ZKTeco periodically changes the information herein which will be incorporated

into new additions/amendments to the manual. ZKTeco reserves the right to add, delete, amend or

modify the information contained in the manual from time to time in the form of circulars, letters,

notes, etc. for better operation and safety of the machine/unit/equipment. The said additions or

amendments are meant for improvement /better operations of the machine/unit/equipment and such

amendments shall not give any right to claim any compensation or damages under any circumstances.

ZKTeco shall in no way be responsible (i) in case the machine/unit/equipment malfunctions due to any

non-compliance of the instructions contained in this manual (ii) in case of operation of the

machine/unit/equipment beyond the rate limits (iii) in case of operation of the machine and equipment

in conditions different from the prescribed conditions of the manual.

The product will be updated from time to time without prior notice. The latest operation procedures

and relevant documents are available on

http://www.zkteco.in.

If there is any issue related to the product, please contact us.

ZKTeco Biometric India Pvt Ltd.

Address

B-1, Khata No.31, Devasandra Industrial Estate,

Whitefield Main Road, Beside Phoenix Mall,

Mahadevapura, Bengaluru, Karnataka.

Phone

080 8628 1342

For business-related queries, please write to us at

sales@zkteco.in.

To know more about our global branches, visit

www.zkteco.in.

Summary of Contents for BG2000 Series


































Search results

Summary of Contents for BG2000 Series

Reviews:

Related manuals for BG2000 Series

Brands by name

Popular brands

ZKTeco BG2000 Series, User Manual

Search results

Summary of Contents for BG2000 Series

Reviews:

Related manuals for BG2000 Series

Brands by name

Popular brands