background image

SBT2000S Swing Barrier Turnstile

 

 

 

 

 

 

  

 

User Manual 

P a g e

 | 14 

 

 Copyright©2020 ZKTECO CO., LTD.  All rights reserved. 

9.

 

Right Gate Closing Deceleration Distance(09EXXX) 

The larger the number, the longer the deceleration time and the more stable the swing arm operation. 
The Right Gate Closing Deceleration Distance value can be set between 10 to 25 and the default value 
is 16. 

10.

 

Gate Closing Delay Time(10EXXX) 

The Gate Closing Delay Time value can be set between 2 to 60 seconds and the default value is 5s. 

11.

 

Clutch Start Angle(11EXXX) 

Set angle at which clutch starts and the valid value of Clutch Start Angle can be set between 1-10. The 
default value is 1. 

12.

 

Clutch Unlock Mode(12EXXX) 

The different Clutch Unlock Modes are as follows:  

 

(12E000) Delayed unlock 

 

(12E001) Swipe to unlock (default) 

13.

 

Fire Opening Direction(13EXXX) 

The different Fire Opening Directions are as follows: - 

 

(13E000) Right open (default) 

 

(13E001) Left open 

 

(13E002) Closed 

14.

 

Volume Setting(14EXXX) 

Adjust the volume of the device as required. The larger the number, the louder the sound. The valid 
value of Volume Setting lies between 0-30 and the default value is 8. 

15.

 

Alarm Tone Setting(15EXXX) 

 

(15E000) Closed 

 

(15E001) Open (default) 

16.

 

In/Out Voice Exchange(16EXXX) 

 

(16E000) Right in, left out (default) 

 

(16E001) Right out, left in 

17.

 

Anti-crush Setting(17EXXX) 

 

(17E000) Stop anti-crush (default) 

 

(17E001) Close  

Summary of Contents for SBT2000S






















Reviews:

Related manuals for SBT2000S