background image

 

 

TS1000: 

  Tripod Turnstile 

TS1011:

  Tripod Turnstile with Controller and RFID Reader 

TS1022: 

  Tripod Turnstile with Controller and Fingerprint Reader with RFID function. 

Please read this document carefully before installation and using the device. 

1.

 

Technical Specifications 

Input Voltage 

AC 100~120V /200~240V,   

50Hz /60Hz 

Max. Tolerance of Arms 

Center: 80 kg 

End: 40 kg 

Rated Power 

60 W 

Ingress Protection Degree 

IP54 

Operating Environment  Indoor and Outdoor (shelter) 

Arm Length (mm) 

520 

Operating Temperature 

-28ºC ~ 60ºC 

Net Weight 

34kg 

Operating Humidity 

5% ~ 85% 

Gross Weight 

40kg 

Flow Rate 

25~30 passages / minute 

Dimension(mm) Figure 1 

L = 520, W = 280, H = 985 

Input Control Signal 

Dry contact 

Package Size (mm) 

L = 600, W = 380, H = 1080 

 

Figure 1

 

 

2. Unpacking and Testing the Tripod Turnstile 

 

2.1 Unpacking 

The vertical type tripod turnstile is top heavy and unsteady, 
do not remove the foam at the bottom before installation, 
as shown in Figure 2-1. 

 

 

 

 

 
 

 
                                                                    

                                                                 

Figure 2-1 

Do not remove the foam lining 

at the bottom before 

installation.

 

Summary of Contents for TS1000 Series













Reviews: