background image

TS200 Series Tripod Turnstile

 

 

 

 

 

 

                            

User Manual 

P a g e

 | 8 

 

 

4.2.2

 

Opening Mode 

Card swiping means that you can open the door only after verification. Free means that you can pass the 
door without verification. Prohibited means that you can't pass the door, whether you have permission or 
not. 

4.2.3

 

Opening Duration 

This function refers to the period of time from opening to closing once the turnstile receives an opening 
signal. In the DIP switch, number 3 is used for duration settings. It can be set two different values: 5s or 10s. 

4.2.4

 

Continue Passing Function 

With the "Continue Passing" function, the turnstile could remember at most 20 swipes of one card at one 
time and allows up to 20 people to pass so they don't have to swipe card each time. This function can be 
enabled or disabled with number 4 in the DIP switch.  

5

 

Equipment Precautions and Maintenance 

 

Precautions 

5.1

 

It is recommended to purchase additional accessories to use the product outdoors. 

1)

 

You may install cooling fans for the equipment if the working temperature is often above 50 ºC. 

2)

 

The device is rated IP54 waterproof under proper installation. However, its ability to stand in 
extreme weather conditions, such as typhoon, is not guaranteed. 

3)

 

If the temperature is around or below -30

º

C, you are recommended to install a heating plate for 

the equipment. You might need to turn the power on multiple times to let the device 
automatically heat up through the self-check program. 

4)

 

The service life of this equipment may be shortened if it works outdoors in coastal areas or a 
region prone to acid rain. 

 

If the power and signal cables are connected properly, this equipment can be immersed under water 
at a depth of 250 mm, but it must not be powered on when it is immersed in water. 

 

It is highly recommended to set a warning card-swiping line to remind passers-by to correctly swipe 
cards at a reasonable distance from the device to prevent passers-by from being squeezed. 

 

It is recommended to place a warning sign at a conspicuous position, and prompt: "

Please swipe 

your card outside the warning line and pass in order. Thank you!

 " 

 

 

Summary of Contents for TS1000D















Reviews:

Related manuals for TS1000D