background image

Pelletherm V.2 M01                                                                                                              51

thermometer). 

10.    Appearing of 

condensation of water 
vapor in the heating 
surfaces of the 
combustion chamber. 

Low temperature of the supply 
water. 
 

It is necessary to set up the thermostat of the 
circulation pump (if such is installed in the 
system). It is recommended that temperature 
for operation of the circulating pump (or the 
temperature of the supply water) to be at least 
65 

o

C. 

11.    Appearing of smoke in 

the boiler room after a 
certain period of 
operation. 
 

Dirty or clogged with ash smoke 
suction fan. 

Cleaning or replacement of smoke suction fan 
- performed by a qualified technician 

Incomplete seal of the door of 
the combustion chamber and/or 
covers, sealing the flue. 

It is necessary tightening/adjustment of the 
door and covers, replacement of the sealing 
ropes - performed by a qualified technician. 

12.    The fuel feeder 

mechanism do not 
operate. 

Opened door of the 
compartment with fuel bunker. 

Switch at the door is actuated, that door should 
be closed. 

Door of the compartment with 
fuel bunker is closed, but there 
is no fuel supply. 

Seek service help - possible mechanical 
damage. 

13.    Others not listed 

above troubles. 

 

It is necessary consultation and/or intervention 
of a service technician. 

 

Table 7.2. Description of errors recorded in the list with "LOG" from the menu of the boiler 

controller. 

 

FAILURE 

CODE 

MESSAGE INDICATED 

ON THE DISPLAY 

FAULT DESCRIPTION 

TROUBLESHOOTING 

10 

[ERROR: IGNITION] 
[FAILED] 

Ignition failed  
 

Clean the burner grate. 
Check the availability of fuel. 
Seek advice from a service 
technician. 

11 

N/A 

Loss of flame during burner 
operation 

Seek service assistance. 
 

12 

[ERROR: PHOTOSENS] 

Error during photosensor operation  Seek service assistance. 

13 

N/A 

Not used 

  

14 

[ERROR: SENSOR A] 
[LOW TEMP] 

The temperature sensor A has 
measured value below 5

o

 

The circulation water is with 
dangerously low temperature and 
its freezing is possible. 
Seek for service help to check 
the heating installation. 

15 

[ERROR: SENSOR A] 
[OVERHEAT] 

The temperature sensor A has 
measured value over 95

o

 

Circulating water is with 
dangerously high temperatures 
and is possible overheating of the 
heating system and equipment. 
Seek service help to check the 
heating installation. 

16 

[ERROR: OPTO-] 
[COUPLER] 

Board error 

Seek service assistance. 

17 

[ERROR: OVER-] 
[PRESSURESENS] 

Not used 

  

18 

[ERROR: FAN 1] 
[ALWAYS ON] 

Combustion air fan can not be 
stopped, possible damage at the 
exit of the controller 

Seek service assistance. 

19 

[ERROR: FAN 1] [STOPP] 

The fan for combustion air does not 
rotate 

Seek service assistance. 

20 

[ERROR: FAN 1 RPM] [] 

The fan for combustion air does not 
rotate at the desired speed 

Seek service assistance. 

21 

N/A 

Not used 

  

22 

[ERROR: STOKER] 
[FAULT] 

Screw error 

Seek service assistance. 

23 

[ERROR: FINAL] 
[COMBUST FAILED] 

Photosensor does not shade during 
the final burn out phase 

Seek service assistance. 

 

Summary of Contents for PELLETHERM SERIES V.2 ?01

























































Reviews: