background image

1

1.Disclaimer

The installation, operation and use of ZX-D60/ ZX-D72 Series module of ZNSHINE SOLAR

AUSTRALIA PTY LTD. are not within the control range of our company. For the loss, damage,
harm or expense caused by the improper installation, handling, use or maintenance, ZNSHINE
SOLAR AUSTRALIA PTY LTD. does not assume any responsibility.

ZNSHINE SOLAR AUSTRALIA PTY LTD. assumes no responsibility for the violation of the

third party patent or other rights due to the use of this module. No license is granted by implication
or as per any patent or patent right.

The specification parameters as mentioned in this manual may be subject to change without

advance notification.

2.Safety precautions

2.1. In the design of photovoltaic system, make sure to consider the voltage changes at

different temperatures (please check the temperature coefficient of each module, when the
temperature falls, the variable output voltage of module will rise).

2.2. Our company requires that each series of PV module string shall be firstly fused and then

connected to other modules strings. For the maximum fuse rating, please refer to the detailed
specifications in the last page.

2.3. Photovoltaic (PV) modules will generate electricity when exposed to the light source. The

arrays composed of multiple modules can cause the fatal electric shock and burn. Personnel
without authorization or training shall be strictly prohibited from contacting PV modules.

2.4. Please use the properly insulated tools and appropriate protective equipment to reduce the

risk of electric shock.

2.5. Please don't trample or stand above the modules.
2.6. Please don't damage or scratch the front or back of module.

2.7. It shall be strictly prohibited from using the modules with damaged glass or base panel on

the top. The damaged modules cannot be repaired and contacting with the module surface may
cause electric shock.

2.8. Please don't disassemble the module or remove any part of it.

2.9. Please keep the plug clean, and don't use contaminated plug for connection.
2.10. Please don't install or operate the wet modules or in the windy weather.
2.11. Please don't connect the positive terminal of individual PV module from that of the cable.

Summary of Contents for ZXM6- TD72- 370/M



















Reviews: