background image

20 

3.2 Spare parts 

Description 

Item number 

Representation 

Hygro Control sensor 

WCE03431 

 

Filter: 

Air (375x445x20) x2 

WSD01908* 

Lateral (555x455x23) 

WSD01909 

Rear (788x400x23) 

WSD01910 

Fan belt 

WGA02968 

* Reference for one part 

 

3.3 Recycling the product 

 

Your appliance has reached the end of its working life

. You would like to dispose of it or replace it. 

Please do not throw it into your dustbin or into your local selective sorting containers. 

 

When this symbol appears on a new appliance, it means that the equipment must not 

be thrown away and that it will be collected selectively so that it can be reused, 

recycled or recovered. Any substances it may contain which are potentially dangerous 

to the environment will be eliminated or neutralised. 

 

You can give it to a community association which will be able to repair it and put it back into circulation. 

If you buy a new appliance, you can take the old one back to the reseller or ask the transporter to take it 

back. 

This is known as a “

One-for-One

” exchange. 

Otherwise please take it to a waste collection centre, if your local council has set up a selective 

collection system for these products. 

 

 
 
 
 

 

 

 

 

3.4 EC compliance certificate 

Z.P.C.E. declares that the products or ranges below: 

SPECIAL POOL DEHUMIDIFIERS 

CAE 508-510-513 

 

are in compliance with the provisions of the: 

 

 ELECTROMAGNETIC COMPATIBILITY directive 89/336/EEC. 

 

 LOW VOLTAGE directive 73/23/EEC, as amended by 93/068/EEC. 

 

The following harmonised standards have been applied: 

EN 60335.2.40 

 

 

 

 

In the context of ongoing improvement, our products are subject to change without notice.      

Version 02/2010 

Give the appliance 

to a community 

association.

 

Take the used device back 

to the reseller when 

making a new purchase. 

 

Take the used 

device to a waste 
collection centre. 

 

EN 

Summary of Contents for CAE





























Reviews: