background image

NOTE:

  To avoid damaging the power cable, do not

 try to twist the entire cable housing (see below).

X

X

X

X

 NOTE:

  To avoid exposing the power cable 

connector pins to water, be sure the connector is 

screwed in all the way and there is no gap 

(see below).

X

X

X

X

4

 General Cleaner 

Operation

 CAUTION

To prevent damage to the cleaner, be sure to adhere 

to the following guidelines:

• 

Remove the cleaner from the pool after the 

cleaning cycle is completed.

• 

Store on the caddy out of direct sunlight or 

inclement weather.

• 

Never lift the cleaner out of the pool by the 

fl oating cable. Always use the lift feature to 

remove cleaner from the pool. 

• 

Take additional care when lifting the cleaner out 

of the pool. It becomes heavier when fi lled with 

water.

• 

Always remove the cleaner from pool when super 

chlorinating or adding acid.

• 

Do not handle cleaner while it is in operation

IMPORTANT

• 

Always make sure the cleaner head is fully 

submerged before you begin operation.

• 

Clean the fi lter canister after each cleaning 

cycle.

• 

Do not leave your cleaner in the pool on a 

permanent basis.

• 

At the end of each cycle, remove the cleaner 

from the pool. 

• 

Start at the cleaner head and untangle any 

coils in the cable before storing the cleaner.

The Evolux robotic cleaner includes a safety 

feature that automatically stops the cleaner if it is 

powered on but not submerged in water. For pools 

equipped with a beach area, this safety feature is 

programmed to drive the cleaner in reverse and 

back into the pool when the impeller is out of the 

water. 

Zodiac recommends not exceeding 3 cleaning 

cycles per week.

Install and Submerge the Cleaner

1.  With the control box plugged into a power 

outlet, spread the fl oating cable across the 

pool deck until you reach the middle of the 

pool length.

2.  At the center point, submerge the cleaner 

in the pool and hold in the vertical position 

to release any air trapped inside. (Figure 

11).

1

Figure 11.  Submerge the Cleaner Vertically

Page

 9 

  

Zodiac

®

 EvoluX

 iQ Robotic Pool Cleaner   

|

   Owner's Manual

Summary of Contents for EvoluX iQ





























Reviews: