background image

Page 5

EziSalt Saltwater Chlorinator   |   Installation Manual

Page 4

EziSalt Saltwater Chlorinator   |   Installation Manual

SAVE THESE INSTRUCTIONS

  

WARNING

People with infectious diseases should not use a spa or hot tub.

To avoid injury, exercise care when entering or exiting the spa or hot tub.

Do not use drugs or alcohol before or during the use of a spa or hot tub to avoid unconsciousness and possible 

drowning.

Before entering a spa or hot tub, measure the water temperature with an accurate thermometer. 

Do not use a spa or hot tub immediately following strenuous exercise.

Prolonged immersion in a spa or hot tub may be injurious to your health.

Do not permit any electric appliance (such as a light, telephone, radio, or television) within 3.5 metres of a spa or 

hot tub.

The use of alcohol, drugs or medication can greatly increase the risk of fatal hyperthermia in hot tubs and spas.
Water temperature in excess of 38°C may be hazardous to your health. 

Attention Installer:  

Install to provide drainage of compartment for electrical components.

     

WARNING

A terminal bar marked "GROUND" is provided within the controller. To reduce the risk of electrical shock which can 

cause serious injury or death, connect this terminal bar to the grounding terminal of your electric service or supply 

panel with a continuous copper conductor having green insulation and one that is equivalent in size to the circuit 

conductors supplying this equipment in accordance with AS/NZ 3000 - 2007. In addition, where required, bonding 

should be extended in accordance with AS/NZ 3000 - 2007 to any metal ladders, water pipes, or other metal within 

3.5 m of the pool/spa.

Summary of Contents for EziSalt





















Reviews: