background image

Page 6

Zodiac

®

 Freerider

 iQ Cordless Robotic Cleaner  |  Owner’s Manual

Section 2.  Cleaner Specifications

2.1  General Specifications

The general specifications for the cleaner are as 

follows:

 WARNING

Only use the battery charger supplied with the cleaner.

Charging Station Supply 

Voltage

110-240 VAC; 50/60 Hz

Supply Voltage

29.4 V DC

Battery Capacity

9.6 Ah

Operating Power

58 W

Cleaner Size (WxDxH)

41 x 42 x 28 cm

Weight of Cleaner

9.1 kg

Packed Weight

15.5 kg

Filtration 

All-purpose filter canister

Cycle Lengths

Variable programming

Charge Temperature

Max 40°C 

Min 5°C

Water Temperature 

Range

Max 35°C 

Min 13°C

Operating Depth

Max 4 m 

Min 40 cm

The cleaner is a double-insulated product. 

A double-insulated electrical appliance is one which 

has been designed in such a way that it does not 

require a safety connection to ground. The basic 

requirement for double-insulation is that no single 

failure can result in dangerous voltage becoming 

exposed so that it might cause an electric shock 

and that this is achieved without relying on an 

earthed (grounded) metal casing. This is achieved 

by having two (2) layers of insulating material 

surrounding live parts or by using reinforced 

insulation. Therefore, devices having double-

insulated construction, such as this cleaner, 

do not use a grounded (three-prong) cord/plug.

2.2  Contents

The packaging should contain the following items:

•  Freerider

 Cleaner

•  Charging Station

•  Removal Hook

•  Transportation Caddy*

•  Remote Control*

* Model FR2000 iQ

Figure 1.  Contents

2.3  Assemble the Charging Station

1.  Insert the top of the charging station foot 

(marked with a blue dot) into the top rear of 

the charging station (also marked with a blue 

dot). Push the lower part of the foot into the 

lower cavity of the charging station until clip 

is secure. 

2.  Attach the hook clip to either charging station 

foot. Attach the hook to the clip.

3.  Run cable through either foot cable slot.

FR1000 iQ

Cable slots

Figure 2.  Assemble Charging Station

Refer to the trolley assembly document for  

trolley assembly instructions.

Summary of Contents for Freerider FR1000 iQ



























Reviews: