background image

14

  

 3.8 I  The remote control (depending on the model)

•  Respect the batt ery polarity.

•  Do not recharge the batt ery, dismantle it or throw it onto a fi re.

•  Do not expose it to high temperatures or direct sunlight.

3.8.1 Switching the remote control on and off 

•  To switch on: press 

.

• 

To switch off : press and hold 

.

Tip: improve the remote control recepti on.

The  frequency  of  the  fl ashing  of  the  led  located  on  the  remote  control  indicates  the  recepti on  quality. 

If the LED fl ashes quickly, recepti on quality is OK.

For the best communicati on between the control box and the remote control:

 -

Positi on the control box on the caddy.

 -

Turn the control box towards the pool

 -

Removal all large obstacles between the control box and the pool. 

3.8.2 Directi ng the cleaner

•  The remote control is equipped with movement sensors to direct the cleaner:

 : Forward

 : Backwards
 : Left  turn

 : Right turn
 : Stop

3.8 Taking the cleaner out of the water (depending on the model)

•  Press 

. The cleaner moves toward the wall and climbs up to the waterline.

 3.8.4 Synchronising the remote control with the control box

By default, the remote control is already synchronised with the control box. If replacing the remote control/control box 

or if a synchronisati on problem occurs, follow the steps below:

•  Place the remote control a 

maximum of 50 cm

 away from the control box. 

• 

Connect the control box, check that the display shows the operati ng ti me, and that no cleaning cycle is running. 

•  Switch on the remote control by pressing 

.

• 

Before the remote control switches to standby (around 45 seconds) press the 

 

  and  

 butt ons simultaneously 

for 6 seconds.

• 

Check that synchronisati on was successful by observing the display and the remote LED:

Display on the 

control box

Remote LED

Result

Good

 

 

 

0:45

2 seconds

Flashing

• 

Synchronisati on successful.

FAIL

On steady

• 

Check  the  distance  between  the  control  box  and  the  remote 

control is 50 cm maximum.

• 

Check the remote control batt eries.  Replace them if necessary. 

If the problem conti nues contact your retailer.

EN

Summary of Contents for Vortex OV 3300
























Reviews: