background image

H0548500.A - EN - 2015-11

7

  

 2.4 I  Opti on connecti on

2.4.1 "Heati ng priority" opti on (depending on model)

•  

This  functi on  helps  to  keep  the  water  temperature  constant  by  checking  the  water  temperature  at  regular  ti me 

intervals (minimum 5 minute cycle every 220 minutes (modifi able ti me)) by fi ltrati on pump control. The fi ltrati on is 

kept operati ng  while the pool temperature is below the temperature requested.

•  

For the connecti on, connect the fi ltrati on ti mer to terminals 1 and 2 and add a shunt between terminals 3 and 4.

1

2

1- 

2 : power for the fi ltrati on pump power contactor coil

: fi ltrati on ti mer
: power contactor (tripolar or bipolar) for the fi ltrati on system 

pump motor

: separate cable for the "heati ng priority" functi on
: heat pump terminal (see wiring diagram § “5.3 I  Wiring 

diagrams”)

: fuse

•  

Modifi cati on of the ti me between 2 fi ltrati on operati ons (value in number of minutes): 

 - press 

 and 

 or 

 at the same ti me for 3 seconds: 

 appears,

 - press  

 unti l the 

 parameter appears, then press  

 or 

 to change the parameter using 

the  

 and 

 keys.

 -

Once the value has been modifi ed, press  

 or 

 to confi rm, 

 - press 

 to exit the menu.

2.4.2 "Remote control" opti on (depending on model)

•  

This opti on enables the device's user interface to be duplicated to enable the device to be controlled by remote. To 

do so, use the remote control kit available as an accessory.

•  

For the connecti on, consult the manual supplied with the kit.

Summary of Contents for Z200 M2

















Reviews: